A flat sheet never stays the length you cut it once it goes through a press brake: the outside of the bend stretches, the inside compresses, and only one layer in between keeps its original length. This free k-factor calculator finds that layer and works out the flat pattern length for a sheet metal bend.
The K-factor presets are published starting values for a medium inside radius (about 1 to 3 times the thickness). The true K-factor depends on your material batch, die opening and press brake, so confirm it with a test bend on production stock before cutting a full run. The bend angle is the rotation from flat: 90 degrees is a right-angle bend. For an obtuse bend with a 120 degree included angle between the flanges, enter 60 degrees. All lengths must use the same unit; inches are shown here, but the formulas work in millimeters too if every length is in millimeters.
Measure each leg from the outside edge to the virtual sharp (apex), the point where the two outside faces would meet if the bend were sharp. The flat pattern length is leg 1 + leg 2 - bend deduction.
Please enter a thickness, radius and leg lengths above 0, a bend angle between 0 and 180 degrees, and a K-factor between 0 and 1.
| K-Factor | Neutral Axis Radius (in) | Bend Allowance (in) | Bend Deduction (in) | Flat Pattern Length (in) |
|---|
Each row uses the thickness, inside radius, bend angle and leg lengths entered above, at a different K-factor. A larger K-factor puts the neutral axis further from the inside face, so the bend allowance grows, the bend deduction shrinks, and the flat pattern gets longer.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A flat sheet never stays the length you cut it once it goes through a press brake: the outside of the bend stretches, the inside compresses, and only one layer in between keeps its original length. This free k-factor calculator finds that layer and works out the flat pattern length for a sheet metal bend. Enter the material thickness, inside bend radius, bend angle and K-factor, plus the two leg lengths, and it shows the bend allowance, the bend deduction, the outside setback and the flat length to cut. The Compare K-Factors tab shows how the flat length changes across the usual K-factor range, so you can see what a wrong K-factor would cost before cutting a full run.
The K-factor is the position of the neutral axis inside a sheet metal bend, expressed as a fraction of the material thickness measured from the inside face. When a sheet bends, the material on the outside of the bend stretches and the material on the inside compresses. Between them sits the neutral axis, the layer that neither stretches nor compresses, so its length is the same before and after bending. If the neutral axis sits a distance t from the inside face of a sheet of thickness T, the K-factor is K = t / T. A K-factor of 0.50 puts the neutral axis at mid-thickness, which is where it sits in a purely elastic bend; in real press brake work it shifts toward the inside face, and published values for common sheet metals fall between about 0.30 and 0.50.
Two numbers describe the same bend from opposite ends. The bend allowance (BA) is the length of the neutral axis arc through the bend, the material the bend consumes. If the flange lengths are measured to the tangent points where the flat meets the curve, the flat length is leg 1 + leg 2 + bend allowance. The bend deduction (BD) starts from the outside dimensions on the drawing, which run to the virtual sharp where the outside faces would meet, and subtracts the material the bend consumes: flat length = leg 1 + leg 2 – bend deduction. Both methods give the same flat length when they use the same K-factor, and this calculator shows both so they can be checked against each other.
The K-factor is the only input that cannot be read off the drawing. It depends on the material, the inside radius relative to the thickness, the die opening and the bending method, and it is determined empirically, usually by bending a coupon of known flat length and measuring the formed part. The presets in this calculator are published starting values for a medium inside radius (about 1 to 3 times the thickness): 0.43 for mild steel in air bending, 0.47 for mild steel in bottom bending, 0.45 and 0.48 for stainless 304, 0.40 for aluminum 5052 and 0.42 for aluminum 6061-T6. Machinery’s Handbook gives 0.446 as an average for mild cold-rolled steel, which is widely used as a general default.
Choose the material and bending method from the preset list, or pick Custom K-factor and enter your own value. The presets cover mild steel, stainless 304 and two aluminum grades in air bending and bottom bending.
Enter the material thickness in inches, the nominal value on the drawing.
Enter the inside bend radius in inches, the radius the tooling actually produces in the part, not the nominal punch radius.
Enter the bend angle in degrees, measured as the rotation from flat. A right-angle bend is 90 degrees. For an obtuse bend with a 120 degree included angle between the flanges, enter 60 degrees, because the sheet only turns through 60 degrees from flat.
Enter the two leg lengths in inches, measured from the outside edge to the virtual sharp (apex) where the two outside faces would meet.
Click Calculate, or just type: the results update as you enter the numbers.
Read the Summary tab for the neutral axis position, the bend allowance, the outside setback, the bend deduction and the flat pattern length, plus a flat-length check worked out by the bend allowance method.
Open the Compare K-Factors tab to see the bend allowance, bend deduction and flat length at K-factors of 0.30, 0.35, 0.40, 0.44 and 0.50 for the same bend.
Neutral axis depth from inside face (in) = K x T Neutral axis radius (in) = R + K x T Bend allowance, BA (in) = angle in degrees x (pi / 180) x (R + K x T) Outside setback, OSSB (in) = (R + T) x tan(angle / 2) Bend deduction, BD (in) = 2 x OSSB - BA Flat pattern length, outside dimensions (in) = leg 1 + leg 2 - BD Flat pattern length, tangent-point legs (in) = (leg 1 - OSSB) + (leg 2 - OSSB) + BA
In these formulas T is the material thickness, R is the inside bend radius, K is the K-factor and the angle is the bend angle in degrees, the rotation from flat. The pi / 180 factor converts the angle to radians, because the bend allowance is an arc length: angle in radians times the neutral axis radius. The outside setback is the distance from the tangent point to the virtual sharp along each flange, and the bend deduction is twice that setback minus the bend allowance, because starting from outside dimensions means removing two straight extensions and restoring one curved length.
The formulas are unit-consistent: every length in inches gives a flat length in inches, and every length in millimeters gives a flat length in millimeters. The bend deduction formula assumes the angle is the rotation from flat; for a right-angle bend the rotation and the included angle between the flanges are both 90 degrees, so the two conventions agree, but for any other angle they differ and the rotation must be used.
Worked setback check at 90 degrees: tan(45 degrees) is 1, so the outside setback equals R + T exactly, and the bend deduction is 2 x (R + T) – BA.
Mild steel sheet 0.125 in thick, bent to 90 degrees on a 0.125 in inside radius, K-factor 0.43 (mild steel, air bending), with outside leg lengths of 2 in and 3 in. All steps below use the unrounded values; displayed figures are rounded only at the end.
Neutral axis depth = 0.43 x 0.125 = 0.05375 in, displayed as 0.0538 in.
Neutral axis radius = 0.125 + 0.05375 = 0.17875 in, displayed as 0.1788 in.
Bend allowance = (90 x pi / 180) x 0.17875 = 1.5707963 x 0.17875 = 0.2807798 in, displayed as 0.2808 in.
Outside setback = (0.125 + 0.125) x tan(45 degrees) = 0.25 x 1 = 0.25 in, displayed as 0.2500 in.
Bend deduction = 2 x 0.25 – 0.2807798 = 0.2192202 in, displayed as 0.2192 in.
Flat pattern length = 2 + 3 – 0.2192202 = 4.7807798 in, displayed as 4.78 in.
Flat length check, bend allowance method = (2 – 0.25) + (3 – 0.25) + 0.2807798 = 4.7807798 in, displayed as 4.78 in. Both methods agree exactly.
So the flat blank should be cut 4.78 in long. The bend consumes 0.2808 in of neutral axis length, and the bend deduction of 0.2192 in is what comes off the 5 in sum of the outside dimensions.
Gives both flat-pattern methods at once: the bend deduction method from outside dimensions and the bend allowance method from tangent-point legs, with the two checked against each other so a mistake shows up immediately.
Presets for real materials and methods: mild steel, stainless 304, aluminum 5052 and 6061-T6 in air bending and bottom bending, from published K-factor tables, with a custom entry for a shop’s own measured value.
Shows what a wrong K-factor costs: the Compare K-Factors tab lists the bend allowance, bend deduction and flat length from K = 0.30 to K = 0.50, so the sensitivity of the flat length to the one uncertain input is visible before cutting.
Handles any bend angle, not just 90 degrees: the angle is the rotation from flat, with guidance for obtuse bends, so acute and obtuse parts use the same calculator.
Works in any unit: the formulas are unit-consistent, so millimeters throughout give a flat length in millimeters, with no conversion step.
Free and instant: no sign-up, no download, and the results update as you type.
Start with the preset for your material and bending method: 0.43 for mild steel in air bending is the common starting point, and Machinery’s Handbook gives 0.446 as an average for mild cold-rolled steel. Those are starting points, not constants. The K-factor shifts with the inside radius, the die opening and the material batch, so for a production run, bend a coupon of known flat length with the production stock and tooling, measure the formed legs, and work backwards to the K-factor that makes the flat length come out right. A first-article check on a single bend is far cheaper than a batch of blanks cut to the wrong length.
Because the bend allowance is an arc length, and the arc the neutral axis sweeps through is the angle the sheet turns through from flat. For a right-angle bend the two angles are both 90 degrees, so it makes no difference. For an obtuse bend with a 120 degree included angle between the flanges, the sheet only turns through 60 degrees, so the arc is a 60 degree arc and the bend allowance uses 60 degrees. Entering the included angle instead would overstate the bend allowance by a factor of two in that case.
They describe the same bend from opposite ends. Bend allowance is the length of the neutral axis arc through the bend, and you add it to flange lengths measured to the tangent points. Bend deduction is the amount subtracted from the sum of the outside dimensions, which run to the virtual sharp. They are not the same number with the sign flipped: the bend deduction is twice the outside setback minus the bend allowance. If you know one and the setback, you can work out the other, and this calculator shows both.
Yes. A tight inside radius pushes the neutral axis toward the inside face, so the K-factor drops; a large radius lets it sit closer to mid-thickness, so the K-factor rises toward 0.50. The published tables reflect this: for mild steel in air bending, the K-factor is about 0.38 for a radius under one thickness, 0.43 for a radius of one to three thicknesses, and 0.50 for a radius over three thicknesses. The presets in this calculator are the medium-radius values, so if your radius is very tight or very generous, pick a lower or higher K-factor, or measure your own.
Yes, with one bend allowance or bend deduction per bend. Work out the bend allowance or deduction for each bend from its own radius, angle and K-factor, then add all the bend allowances to the straight legs measured between tangent points, or subtract all the bend deductions from the sum of the outside dimensions. This calculator covers one bend at a time, so run it once per bend and combine the results. Parts with bends in different directions or with hems and joggles need extra allowances that a single-bend calculation does not cover.
This calculator gives flat pattern estimates for a single sheet metal bend with a constant inside radius, based on the dimensions and K-factor you enter. The K-factor is an empirical value that varies with the material batch, the inside radius, the die opening and the bending method, so the presets are starting points and the true value for your shop should be confirmed with a test bend on production stock before cutting a full run. Springback, material thickness tolerance, grain direction and tooling wear all move the finished dimensions. The results are for planning and estimating only; verify the first article against the drawing before releasing a batch.
ADVERTISEMENT
ADVERTISEMENT