Pitch Diameter Calculator

The pitch diameter is the diameter that decides whether a bolt and a nut actually fit together, yet it is the one diameter you cannot read straight off a pair of calipers. This free pitch diameter calculator works it out from the two numbers you do know: the major diameter and the pitch.

Thread System and Size

The major diameter is the nominal thread size: 10 mm for an M10 bolt, or 0.25 in for a 1/4 in bolt. For metric threads enter the pitch in millimetres (1.5 for M10 coarse); for inch threads enter the threads per inch (20 for 1/4-20 UNC). Both systems use the same 60 degree profile, so the pitch diameter formula is the same in both.

Diameters
Pitch diameter
Basic minor diameter
Thread profile
Fundamental triangle height (H)
External thread depth (per side)
Pitch
Pitch
Threads per inch
Note: these are basic (nominal) profile dimensions from ISO 68-1 and ASME B1.1, with no tolerance class applied. A real bolt or nut is made to a tolerance class (6g/6H for metric, 2A/2B for inch), so its measured pitch diameter sits slightly below (external) or above (internal) the basic value shown here. The minor diameter shown is the basic minor diameter; the external thread root diameter is a little smaller again.
Pitch (mm)Pitch Diameter (mm)Minor Diameter (mm)Thread Depth (mm)

Each row uses the major diameter entered above, at a different pitch. A coarser pitch (larger pitch, fewer TPI) cuts deeper, so both the pitch diameter and the minor diameter fall as the pitch grows.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

Introduction

The pitch diameter is the diameter that decides whether a bolt and a nut actually fit together, yet it is the one diameter you cannot read straight off a pair of calipers. This free pitch diameter calculator works it out from the two numbers you do know: the major diameter and the pitch. Enter an M10 x 1.5 metric thread or a 1/4-20 UNC inch thread and it shows the pitch diameter, the basic minor diameter, the fundamental triangle height and the thread depth, in millimetres and inches. The Compare Pitches tab shows how those diameters change across pitches for the same major diameter, so you can see at a glance what a coarser or finer pitch does to the thread.

What is a Pitch Diameter Calculator?

The pitch diameter is the diameter of an imaginary cylinder that cuts through the thread where the ridge and the groove are exactly the same width. It sits between the major diameter (crest to crest) and the minor diameter (root to root), and it is the diameter that thread tolerances and gauges are defined around, because it is where mating threads actually bear on each other. Two threads with the same major diameter but different pitches have different pitch diameters, which is why the pitch diameter, not the outside diameter, is the number a machinist checks.

Both ISO metric and Unified inch threads use a 60 degree V profile, so the same geometry gives the pitch diameter in both systems: subtract 0.649519 times the pitch from the major diameter. For inch threads the pitch is 1 divided by the threads per inch, so a 1/4-20 UNC thread has a pitch of 0.0500 in and a pitch diameter of 0.2175 in. The basic minor diameter follows the same pattern with a larger factor: subtract 1.082532 times the pitch from the major diameter. These are basic (nominal) profile dimensions, with no tolerance class applied: a real bolt is made slightly under the basic pitch diameter and a real nut slightly over it, so the two assemble with clearance.

If you need the full set of dimensions for a standard size, including the tap drill and the clearance hole, the Thread Calculator covers that from the size designation alone. If you only know the threads per inch or a measured pitch, the Thread Pitch Calculator converts between TPI and pitch and matches the result to the nearest standard thread.

How to Use the Pitch Diameter Calculator

  1. Choose the thread system: Metric (ISO) or Unified Inch (UNC/UNF). The input boxes change to match.
  2. Enter the major diameter: the nominal size in millimetres for metric (10 for M10), or in decimal inches for inch threads (0.25 for a 1/4 in bolt).
  3. Enter the pitch in millimetres for metric threads (1.5 for M10 coarse), or the threads per inch for inch threads (20 for 1/4-20 UNC).
  4. Click Calculate, or just type: the results update as you enter the numbers.
  5. Read the Summary tab for the pitch diameter, basic minor diameter, fundamental triangle height, external thread depth and the pitch in both units.
  6. Open the Compare Pitches tab to see the pitch diameter, minor diameter and thread depth across a range of pitches at the same major diameter.

Formula

Fundamental triangle height, H = 0.866025 x P

Pitch diameter, d2 = d – 0.649519 x P

Basic minor diameter, d1 = d – 1.082532 x P

External thread depth (per side) = 0.613435 x P

Pitch, inch threads (in) = 1 / TPI

Pitch (mm) = 25.4 / TPI

Threads per inch = 25.4 / pitch (mm)

In these formulas d is the major diameter (nominal size) and P is the pitch, both in the same unit. The constants come from the geometry of the 60 degree fundamental triangle. The triangle height H is the square root of 3 divided by 2 times the pitch, which is 0.866025 x P. The pitch line sits 3H/8 below the crest, so the pitch diameter is the major diameter less 2 x 3H/8, which works out to 0.649519 x P. The basic minor diameter sits 5H/8 below the crest on each side, giving 1.082532 x P. The external thread depth of 0.613435 x P is the distance from the crest flat to the rounded root of an external thread, which reaches a little deeper than the basic minor diameter.

These formulas give basic profile dimensions. They do not include the allowances and tolerances of a class of fit (6g/6H for metric, 2A/2B for inch), so a manufactured part measures slightly different from the basic values, by design.

Worked Example

An M10 x 1.5 metric coarse thread. All steps below use the unrounded values; displayed figures are rounded to three decimals (mm) or four decimals (in) only at the end.

Fundamental triangle height H = 0.866025 x 1.5 = 1.2990375 mm, displayed as 1.299 mm (0.0511 in).

Pitch diameter d2 = 10 – 0.649519 x 1.5 = 10 – 0.9742785 = 9.0257215 mm, displayed as 9.026 mm (0.3553 in).

Basic minor diameter d1 = 10 – 1.082532 x 1.5 = 10 – 1.623798 = 8.376202 mm, displayed as 8.376 mm (0.3298 in).

External thread depth = 0.613435 x 1.5 = 0.9201525 mm, displayed as 0.920 mm (0.0362 in).

Threads per inch = 25.4 / 1.5 = 16.9333, displayed as 16.93 TPI.

So an M10 x 1.5 thread has a pitch diameter of 9.026 mm and a basic minor diameter of 8.376 mm, matching the published ISO metric chart values.

Inch check, 1/4-20 UNC: pitch = 1 / 20 = 0.0500 in. Pitch diameter = 0.25 – 0.649519 x 0.05 = 0.25 – 0.03247595 = 0.21752405 in, displayed as 0.2175 in (5.525 mm). Basic minor diameter = 0.25 – 1.082532 x 0.05 = 0.25 – 0.0541266 = 0.1958734 in, displayed as 0.1959 in (4.975 mm). Both match the published ASME B1.1 basic dimensions for 1/4-20.

Benefits of Using a Pitch Diameter Calculator

  • Works for both thread systems: metric threads by pitch in millimetres, inch threads by TPI, with the same 60 degree profile geometry behind both.
  • Shows every profile dimension at once: pitch diameter, basic minor diameter, triangle height and thread depth, each in millimetres and inches.
  • Compares pitches side by side: the Compare Pitches tab shows how the diameters fall as the pitch gets coarser, which makes the trade-off between coarse and fine threads easy to see.
  • Matches the published charts: M10 x 1.5 gives 9.026 mm and 1/4-20 UNC gives 0.2175 in, exactly the values in the ISO and ASME basic dimension tables.
  • Catches impossible inputs: a pitch too coarse for the diameter gives a clear error instead of a negative diameter.
  • Free and instant: no sign-up, no download, and the results update as you type.

Frequently Asked Questions

What is pitch diameter, and why does it matter more than the major diameter?

The pitch diameter is the diameter of an imaginary cylinder that passes through the thread where the ridge and the groove are equally wide. It matters because it is the diameter where mating threads actually contact each other, so it is the diameter that fit, strength and gauging are defined around. The major diameter is just the outside of the bolt: two bolts can share a major diameter and still not interchange if their pitches differ, because their pitch diameters differ. When a drawing calls out a thread tolerance class, the limits are given on the pitch diameter.

Is the pitch diameter formula the same for metric and inch threads?

Yes. Both ISO metric and Unified inch threads use a 60 degree V profile with the same basic geometry, so the pitch diameter is the major diameter minus 0.649519 times the pitch in both systems. The only difference is how the pitch is given: directly in millimetres for metric threads, and as threads per inch for inch threads, where the pitch is 1 divided by TPI. A 1/4-20 UNC thread has a pitch of 0.05 in, and the same formula gives its 0.2175 in pitch diameter.

What is the difference between the basic minor diameter and the root diameter?

The basic minor diameter (d1 = d – 1.082532 x P) is the diameter at the bottom of the basic profile, where the internal thread crests sit. The external thread root diameter (d3 = d – 1.226869 x P for metric threads) is a little smaller, because the root of a real external thread is rounded and cuts slightly deeper than the basic profile. The tap drill for an internal thread is chosen near the basic minor diameter, while the root diameter is the number used for bolt strength calculations. This calculator shows the basic minor diameter, which is the value thread charts list.

Why is my measured pitch diameter different from this calculator?

This calculator gives the basic (nominal) pitch diameter with no tolerance class applied. A real external thread is made to a class such as 6g (metric) or 2A (inch), which puts its pitch diameter below the basic value by an allowance plus a tolerance; a real internal thread is made above it. So a measured bolt should read a little under the basic value, and a measured nut a little over it. If the difference is much larger than the class allowance, check that you measured the right thread: a wrong pitch, a worn thread or a different series (UNF instead of UNC) all shift the pitch diameter.

How do I measure pitch diameter on a real bolt?

The standard shop method is the three-wire method: three precision wires of a known diameter are laid in the thread grooves, a micrometer measures across the wires, and the pitch diameter is worked out from that measurement, the wire diameter and the pitch. Thread micrometers and pitch-diameter gauges measure it directly. Calipers alone cannot measure pitch diameter, because their jaws sit on the crests and read the major diameter instead. Whatever method you use, measure at room temperature and away from any damaged or worn section of the thread.

Disclaimer

This calculator gives basic (nominal) thread profile dimensions from the ISO 68-1 and ASME B1.1 geometry, with no tolerance class, allowance or manufacturing variation applied. Real threads are made to tolerance classes (6g/6H for metric, 2A/2B for inch) and measure slightly different from the basic values by design. The results are for reference, estimating and checking only. Do not use them as the sole basis for cutting a thread, accepting or rejecting a part, or any safety-critical joint; check the drawing, the applicable standard and the thread gauge for the job.

ADVERTISEMENT

ADVERTISEMENT