Thread Calculator

Every thread designation packs a full set of dimensions into a few characters: M10 x 1.5 or 1/4-20 UNC tells you the size, the pitch and the series, but not the pitch diameter, the minor diameter or the drill sizes you actually need at the bench. This free thread calculator unpacks the designation for you.

Thread Series and Size

Pick the series first, then the size. Metric sizes are written as diameter x pitch in millimetres (M10 x 1.5); inch sizes are written as diameter, threads per inch and series (1/4-20 UNC). Every size in the list is a standard stocked size, and every tap drill and clearance hole comes from the published charts for that size.

Basic diameters
Major diameter
Pitch diameter
Basic minor diameter
Thread depth, basic profile (per side)
Pitch
Pitch
Threads per inch
Drills
Tap drill (cutting tap, about 75% thread)
Clearance hole, close fit
Clearance hole, normal fit
Clearance hole, loose fit
Note: diameters are basic (nominal) profile dimensions from ISO 68-1 and ASME B1.1, with no tolerance class applied. Tap drills are the standard cutting-tap sizes for about 75 percent thread engagement (ISO 2306 for metric, Machinery's Handbook for inch). Clearance holes follow ISO 273 (metric) and ASME B18.2.8 (inch). The tap drill and the clearance drill are different holes: the tap drill is smaller than the bolt so the tap can cut threads into it, while the clearance hole is larger than the bolt so it slides through.
SizePitch (mm)Pitch Dia (mm)Minor Dia (mm)Tap DrillClearance (Normal)

Each row is one size in the selected series, with its pitch, basic diameters, tap drill and normal-fit clearance hole. Switch the series above to compare a different family of threads.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

Introduction

Every thread designation packs a full set of dimensions into a few characters: M10 x 1.5 or 1/4-20 UNC tells you the size, the pitch and the series, but not the pitch diameter, the minor diameter or the drill sizes you actually need at the bench. This free thread calculator unpacks the designation for you. Pick a metric coarse, metric fine, UNC or UNF thread from the list of standard sizes and it shows the major, pitch and minor diameters, the pitch and TPI, the tap drill size and the clearance hole in all three fits. The Compare Sizes tab lists every size in the selected series side by side, so you can pick the size that fits the job instead of guessing from a chart.

What is a Thread Calculator?

A thread calculator turns a thread designation into the dimensions that matter for making and assembling the joint. The designation gives two numbers: the nominal major diameter and the pitch (in millimetres for metric threads, as threads per inch for inch threads). Every other diameter follows from the 60 degree V profile: the pitch diameter is the major diameter less 0.649519 times the pitch, the basic minor diameter is the major diameter less 1.082532 times the pitch, and the basic profile depth is 0.541266 times the pitch per side. Those are basic (nominal) dimensions, the same numbers the ISO 724 and ASME B1.1 tables list.

The two drill sizes are just as important as the diameters. The tap drill is the hole you drill before cutting an internal thread with a tap: it is smaller than the bolt, leaving material for the tap to cut into, and the standard sizes give about 75 percent thread engagement. The clearance hole is the hole a bolt passes through without threading into: it is larger than the bolt, and it comes in three fits, close for accurate location, normal for general work and loose where parts may not line up exactly. Mixing the two up is a classic mistake: a 1/4-20 bolt will not pass through its own #7 tap drill hole. If you need a clearance hole for a size outside this calculator’s list, or want the fits explained in full, the Clearance Hole Calculator covers every size from #0 to 1 inch and M1.6 to M30.

If you already know the major diameter and pitch but the size is not in the list, the Pitch Diameter Calculator works out the diameters for any combination. If you only know the TPI or a measured pitch, the Thread Pitch Calculator converts between the two and matches the result to the nearest standard thread.

How to Use the Thread Calculator

  1. Choose the thread series: Metric Coarse, Metric Fine, UNC or UNF. The size list changes to match.

  2. Choose the size designation: M10 x 1.5 for metric, 1/4-20 UNC for inch threads.

  3. Click Calculate, or just pick: the results update as you change the selection.

  4. Read the Summary tab for the major, pitch and minor diameters, the basic profile depth, the pitch and TPI, the tap drill and the three clearance hole fits.

  5. Open the Compare Sizes tab to see every size in the selected series with its pitch, diameters, tap drill and normal-fit clearance hole.

Formula

Pitch, inch threads (in) = 1 / TPI

Pitch (mm) = 25.4 / TPI

Threads per inch = 25.4 / pitch (mm)

Pitch diameter, d2 = d – 0.649519 x P

Basic minor diameter, d1 = d – 1.082532 x P

Basic profile depth (per side) = 0.541266 x P

Metric tap drill (cutting tap, about 75% thread) = d – P, rounded to the nearest standard drill

Inch tap drill (cutting tap, about 75% thread) = d – 0.01299 x 75 / TPI, rounded to the nearest standard drill

In these formulas d is the major diameter and P is the pitch, both in the same unit. The diameter factors come from the 60 degree fundamental triangle: the pitch line sits 3H/8 below the crest and the basic minor diameter sits 5H/8 below the crest on each side, where H = 0.866025 x P. The basic profile depth of 0.541266 x P is 5H/8, the distance from the crest flat to the basic minor diameter.

The tap drill rules are the standard shop rules, not profile geometry. For metric threads the cutting-tap drill is the diameter minus the pitch (ISO 2306): M10 x 1.5 takes an 8.5 mm drill. For inch threads the Machinery’s Handbook formula gives the exact hole for a chosen thread percentage, and the chart value is the nearest standard number, letter or fractional drill: 1/4-20 UNC takes a #7 drill (0.2010 in), which gives about 75 percent thread. Clearance holes are table values, not formulas: ISO 273 for metric (fine, medium and coarse series) and ASME B18.2.8 for inch (close, normal and loose fits).

Worked Example

An M10 x 1.5 metric coarse thread. All steps below use the unrounded values; displayed figures are rounded to three decimals (mm) or four decimals (in) only at the end.

Pitch diameter d2 = 10 – 0.649519 x 1.5 = 10 – 0.9742785 = 9.0257215 mm, displayed as 9.026 mm (0.3553 in).

Basic minor diameter d1 = 10 – 1.082532 x 1.5 = 10 – 1.623798 = 8.376202 mm, displayed as 8.376 mm (0.3298 in).

Basic profile depth = 0.541266 x 1.5 = 0.811899 mm, displayed as 0.812 mm (0.0320 in).

Threads per inch = 25.4 / 1.5 = 16.9333, displayed as 16.93 TPI.

Tap drill = 10 – 1.5 = 8.5 mm (ISO 2306).

Clearance holes (ISO 273): close 10.5 mm, normal 11.0 mm, loose 12.0 mm.

So an M10 x 1.5 bolt has a 9.026 mm pitch diameter, needs an 8.5 mm hole before tapping, and passes through an 11.0 mm hole at the normal clearance fit.

Inch check, 1/4-20 UNC: pitch = 1 / 20 = 0.0500 in (1.270 mm). Pitch diameter = 0.25 – 0.649519 x 0.05 = 0.21752405 in, displayed as 0.2175 in (5.525 mm). Basic minor diameter = 0.25 – 1.082532 x 0.05 = 0.1958734 in, displayed as 0.1959 in (4.975 mm). Basic profile depth = 0.541266 x 0.05 = 0.0270633 in, displayed as 0.0271 in (0.687 mm). Tap drill #7 (0.2010 in). Clearance holes (ASME B18.2.8): close F (0.2570 in), normal 17/64 in (0.2656 in), loose 9/32 in (0.2812 in).

Benefits of Using a Thread Calculator

  • Gives the whole job in one place: diameters, pitch, TPI, tap drill and all three clearance fits, instead of three separate charts.

  • Uses standard sizes only: every size in the list is a stocked ISO or ASME size, with tap drills and clearance holes taken from the published charts for that size.

  • Covers both systems: metric coarse and fine, UNC and UNF, with every figure in millimetres and inches.

  • Compares a whole series at once: the Compare Sizes tab lists every size in the series, which makes it easy to step up or down a size and see what changes.

  • Keeps the two drills apart: the tap drill and the clearance hole are shown side by side with their different sizes, so the classic mix-up is easy to avoid.

  • Free and instant: no sign-up, no download, and the results update as you change the selection.

Frequently Asked Questions

What is the difference between UNC and UNF?

UNC (Unified National Coarse) and UNF (Unified National Fine) are the two general-purpose series of the Unified inch thread system, and they differ only in pitch at a given diameter. A 1/4 in UNC thread has 20 threads per inch; the same diameter in UNF has 28. Coarse threads are the general-purpose default: they are faster to assemble, more forgiving of dirt and damage, and better in soft materials. Fine threads give finer adjustment, a slightly larger stress area and better resistance to loosening from vibration, and they are common in precision and high-strength work. A UNC nut will not fit a UNF bolt of the same diameter, because the pitches differ.

Why is the tap drill smaller than the bolt, and the clearance hole larger?

Because they do opposite jobs. The tap drill makes the hole that a tap then cuts threads into, so it must leave material for the tap to remove: for M10 x 1.5 the 8.5 mm hole is smaller than the 10 mm bolt, and the tap cuts the thread into the remaining 1.5 mm of material around the hole. The clearance hole is a plain hole the bolt slides through without threading into, so it must be larger than the bolt: an M10 bolt needs an 11.0 mm hole at the normal fit. Drilling a clearance hole with the tap drill size is one of the most common workshop mistakes, and the bolt will not pass through.

What does 75 percent thread mean for a tap drill?

It means the tap cuts threads to 75 percent of the full theoretical thread depth. A 100 percent thread would need a hole exactly at the basic minor diameter, which makes tapping very hard and risks breaking the tap, for almost no extra strength: most of a thread’s holding power comes from the first half of its depth. The standard cutting-tap drills in this calculator give about 75 percent thread, which is the usual compromise for general work in steel. For soft materials or hard tapping, a larger drill giving 50 to 65 percent thread is often used instead.

Can I use a metric tap drill chart for an inch thread?

No, not directly. The metric rule (drill = diameter minus pitch) works because metric pitches are given in millimetres and the standard drills are metric sizes. Inch threads need the Machinery’s Handbook formula (drill = major diameter minus 0.01299 x percent thread divided by TPI) and the nearest number, letter or fractional drill, which is a different set of sizes. The two systems do line up sometimes by coincidence (a 5.1 mm drill is close to a #7), but the chart value for the actual thread is the one to use. This calculator gives the correct drill for each system.

What is the difference between the basic minor diameter and the tap drill size?

The basic minor diameter is a profile dimension: the diameter at the bottom of the basic thread profile, 8.376 mm for M10 x 1.5. The tap drill is the hole you actually drill before tapping, 8.5 mm for the same thread. The tap drill is deliberately a little larger than the basic minor diameter, because a hole exactly at the minor diameter would give a 100 percent thread and make tapping very difficult. The 8.5 mm drill gives about 77 percent thread, which is strong enough for general work and much easier to tap. So the tap drill is a practical shop value, while the minor diameter is the geometric reference it is based on.

Disclaimer

This calculator gives basic (nominal) thread dimensions from the ISO 68-1 and ASME B1.1 geometry, with no tolerance class, allowance or manufacturing variation applied, and standard tap drill and clearance hole sizes from ISO 2306, ISO 273, ASME B18.2.8 and Machinery’s Handbook for cutting taps at about 75 percent thread engagement. Real threads are made to tolerance classes (6g/6H for metric, 2A/2B for inch) and measure slightly different from the basic values by design. Form taps, coated taps, hard or soft materials and deep holes all change the best drill size. The results are for reference and general workshop use only. Do not use them as the sole basis for cutting a thread, accepting or rejecting a part, or any safety-critical joint; check the drawing, the applicable standard and the tap manufacturer’s recommendation for the job.

ADVERTISEMENT

ADVERTISEMENT