Pick a rivet too short and the shop head comes out undersized; pick one too long and the shank bends or clinches instead of forming a proper head. This free rivet size calculator gets the length right for solid rivets.
Grip is the total thickness of all the layers being joined, measured with the joint clamped together. The thickest single sheet is used for the diameter check: the FAA rule of thumb is a rivet diameter at least 3 times the thickest sheet. Shear strengths are the FAA driven values for solid aluminum rivets.
Please enter values above 0 for the grip thickness and the thickest sheet.
| Rivet Diameter | Recommended Length (in) | Hole Size (in) | Single Shear per Rivet (lbf) |
|---|
Each row uses the grip thickness and rivet material entered above, at a different standard rivet diameter. Length grows with diameter because the shop head allowance is 1.5 times the diameter, and shear strength grows with the square of the diameter.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
Pick a rivet too short and the shop head comes out undersized; pick one too long and the shank bends or clinches instead of forming a proper head. This free rivet size calculator gets the length right for solid rivets. Enter the total grip thickness of the layers being joined, the thickest single sheet and the rivet diameter, and it gives the recommended rivet length, the nearest standard length, the hole size to drill and a single-shear strength estimate for the rivet, plus a check that the diameter meets the FAA 3x rule for the sheet thickness.
A rivet size calculator works out which solid rivet fits a joint. A solid rivet is a plain metal pin with a factory head on one end; it is pushed through a drilled hole and the tail is upset with a rivet gun and bucking bar to form a second head, the shop head, on the other side. The length that matters is the shank below the factory head, and it has two parts: the grip, which is the total thickness of all the layers being joined, and the allowance, which is the extra shank that gets smashed into the shop head.
The FAA rule for the allowance is 1.5 times the rivet diameter, so the recommended length is grip plus 1.5 times the diameter. The hole is drilled slightly larger than the rivet, about 0.004 inches of clearance, so the rivet drops in without dragging but still swells tight against the hole wall when driven. The diameter itself should be at least 3 times the thickest single sheet, another FAA rule of thumb, because a thin rivet in thick sheet can shear off under load.
Shop head allowance (in) = 1.5 x rivet diameter
Recommended rivet length (in) = grip thickness + 1.5 x rivet diameter
Nearest standard length (in) = recommended length rounded up to the next 1/16 in
Hole size (in) = rivet diameter + 0.004 in clearance
Rivet cross-section (sq in) = pi x diameter squared / 4
Single shear strength per rivet (lbf) = shear strength (psi) x cross-section
Minimum diameter by the 3x rule (in) = 3 x thickest single sheet
Shear strengths (FAA driven values for solid aluminum rivets): aluminum 1100 (code A) 10,000 psi, aluminum 2117-T4 (code AD) 30,000 psi, aluminum 2024-T4 (code DD) 41,000 psi. The 2117-T4 rivet is the common general-repair aircraft rivet: it drives cold, needs no heat treatment and is highly corrosion resistant.
The length is measured below the manufactured head for protruding-head rivets. Countersunk rivets are normally measured over their full length including the head, so check the applicable standard for the head style being used.
Two sheets with a total grip of 0.125 inches, thickest sheet 0.04 inches, joined with a 1/8 inch diameter 2117-T4 aluminum rivet (30,000 psi shear strength). All steps below use the unrounded values; displayed figures are rounded to four decimals for lengths and two decimals for force.
Shop head allowance = 1.5 x 0.125 = 0.1875 in.
Recommended length = 0.125 + 0.1875 = 0.3125 in.
Nearest standard length = 0.3125 in, which is exactly 5/16 in, so no rounding up is needed.
Hole size = 0.125 + 0.004 = 0.1290 in.
Cross-section = pi x 0.125 squared / 4 = 0.0122718 sq in.
Single shear strength = 30,000 x 0.0122718 = 368.1552 lbf, displayed as 368.16 lbf.
Minimum diameter by the 3x rule = 3 x 0.04 = 0.1200 in; the chosen 0.125 in diameter meets the rule, so the check passes.
So the joint takes a 1/8 inch rivet, 5/16 inch long, in a 0.1290 inch hole, with about 368 lbf of single shear strength per rivet.
Because the extra length is the raw material for the shop head. The shank must stick out past the back of the joint by 1.5 times its diameter before driving, and that protruding metal is upset into the second head. Too little protrusion gives an undersized shop head that can pull through; too much lets the shank bend or clinch instead of forming a clean head. The finished shop head is about 1.5 diameters across.
A numbered drill bit, not a fractional one: a number 40 bit (0.098 in) for a 3/32 rivet, a number 30 bit (0.1285 in) for a 1/8 rivet, and a number 11 bit (0.191 in) for a 3/16 rivet. Each leaves about 0.004 inches of clearance, which is what this calculator uses. A fractional bit the same size as the rivet leaves no clearance at all and the rivet will not drop in.
The rivet diameter should be at least 3 times the thickness of the thickest single sheet in the joint. It comes from FAA sheet metal practice and keeps the joint in the range where the rivet is strong enough in shear without being so large that it distorts the sheet. If the calculator warns that the diameter is below the 3x rule, step up to the next diameter size.
No. Blind rivets size differently: their grip range is set by the manufacturer, and the stem pull leaves only a small protrusion (about 3/64 to 1/8 inch) before setting. This calculator covers solid rivets only, the type driven with a rivet gun and bucking bar. For blind rivets, use the grip range printed on the manufacturer’s datasheet.
That depends on the total load on the joint, the spacing and edge distance rules, and whether the rivets are in single or double shear, which is a joint design question this calculator does not answer. As a starting point, divide the total shear load by the single shear strength per rivet shown here, then apply the applicable standard’s spacing rules (pitch at least 3 times the diameter between rivets) and have the joint checked by a qualified person for any structural or aircraft work.
This calculator gives preliminary solid rivet sizes from FAA rules of thumb and published alloy shear strengths. It is not a joint design tool and does not replace the applicable standard, maintenance manual or engineering check. Structural joints, aircraft repairs and any safety-critical fastening need proper design for the loads, edge distance, spacing, material compatibility and inspection requirements involved. Do not substitute a lower-strength rivet alloy without making up the difference with a larger size, as the FAA guidance requires.
ADVERTISEMENT
ADVERTISEMENT