Bending Stress Calculator

How hard is a beam’s material working at its most stressed point? This free bending stress calculator finds the maximum bending stress in a beam from the bending moment and the cross-section.

Bending Moment and Section

Enter the bending moment at the cross-section you are checking, usually the maximum moment from the shear and moment diagram. For an I-beam, channel or other rolled shape, choose "I-beam or other shape" and enter I and c from the steel section tables: for a symmetric I-beam, c is half the overall depth. The moment is converted to lb-in inside the calculator (1 lb-ft = 12 lb-in).

Maximum bending stress
Maximum bending stress
Maximum bending stress
Section properties
Moment of inertia I
Section modulus S
Distance to extreme fiber c
Bending moment used
Note: the flexure formula assumes Euler-Bernoulli bending: plane sections stay plane, the material stays linearly elastic, the beam is prismatic, and the load acts in a plane of symmetry. The stress shown is the extreme-fiber stress at the outer top and bottom surfaces, tension on one side and compression on the other, and it is zero at the neutral axis. This calculator checks bending stress only: shear stress, buckling, deflection and connections all need separate checks.
Bending MomentStress (psi)Stress (ksi)

Each row uses the section entered above, at a different bending moment. Bending stress grows in direct proportion to the moment, so doubling the moment doubles the stress.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

Introduction

How hard is a beam’s material working at its most stressed point? This free bending stress calculator finds the maximum bending stress in a beam from the bending moment and the cross-section. Enter the moment in lb-ft, pick a rectangular or circular section or enter I and c directly for an I-beam, and it shows the moment of inertia, the section modulus, the distance to the extreme fiber and the maximum bending stress in psi and ksi. The Compare Moments tab shows how the stress grows as the moment grows, which is the quickest way to see how much headroom a section has.

What is a Bending Stress Calculator?

Bending stress is the normal stress a bending moment creates in a beam’s cross-section. When a beam bends, the material on one side of the neutral axis stretches and the material on the other side compresses, and the stress varies linearly from zero at the neutral axis to a maximum at the outer surfaces. For a beam sagging under a downward load, the bottom fibers are in tension and the top fibers are in compression; the calculator reports the magnitude, which is the same on both sides for a symmetric section.

The governing equation is the flexure formula: sigma = M x c / I, where M is the bending moment at the section, c is the distance from the neutral axis to the extreme outer fiber, and I is the second moment of area of the cross-section about the bending axis. The compact form uses the section modulus S = I / c, giving sigma = M / S. The two forms are the same equation: S simply combines the section’s geometry into one number, so a larger S means a lower stress for the same moment.

For a rectangle, I = b x h cubed / 12, c = h / 2 and S = b x h squared / 6. For a solid circle, I = pi x d to the fourth / 64, c = d / 2 and S = pi x d cubed / 32. For an I-beam, channel or any other rolled shape, I and c come from the steel section tables, which is why the calculator lets you enter them directly: for a symmetric I-beam, c is half the overall depth.

Stress is only one of the checks a beam needs: the Beam Deflection Calculator checks the sag against L/360 and L/240, and the Beam Load Calculator works out the largest load the same beam can carry.

How to Use the Bending Stress Calculator

  1. Enter the bending moment M in lb-ft, at the cross-section you are checking. This is usually the maximum moment from the shear and moment diagram.
  2. Choose the section type: Rectangle, Solid circle, or “I-beam or other shape (enter I and c)”.
  3. For a rectangle enter the width and depth in inches; for a circle enter the diameter; for an I-beam or other shape enter I in in^4 and c in inches from the section tables.
  4. Click Calculate, or just type: the results update as you enter the numbers.
  5. Read the Summary tab for the maximum bending stress in psi and ksi, plus I, S, c and the moment in lb-in.
  6. Open the Compare Moments tab to see the stress at half, one, one and a half and two times the entered moment, for the same section.

Formula

Maximum bending stress (psi) = bending moment (lb-in) x c (in) / I (in^4)

Maximum bending stress (psi) = bending moment (lb-in) / S (in^3)

Section modulus (in^3) = I (in^4) / c (in)

Rectangle: I = b x h cubed / 12, c = h / 2, S = b x h squared / 6

Solid circle: I = pi x d to the fourth / 64, c = d / 2, S = pi x d cubed / 32

Bending moment (lb-in) = bending moment (lb-ft) x 12

Stress (ksi) = stress (psi) / 1,000

The two stress formulas are identical: substituting S = I / c into M / S gives M x c / I. The moment conversion matters: a moment entered as 10,000 lb-ft is 120,000 lb-in, and forgetting the factor of 12 understates the stress by twelve times. Stress is linear in the moment, so doubling the moment doubles the stress, and linear in c and inversely proportional to I, so a deeper section lowers the stress twice over: it raises I and it raises S.

The flexure formula assumes Euler-Bernoulli bending: plane sections remain plane after bending, the material is linearly elastic, the beam is prismatic, and the load acts in a plane of symmetry. It gives the stress at the extreme fiber only; the stress at any other depth is proportional to its distance from the neutral axis.

Worked Example

A rectangular beam, 6 in wide and 12 in deep, with a bending moment of 10,000 lb-ft. All steps below use the unrounded values; displayed figures are rounded only at the end.

Bending moment in lb-in = 10,000 x 12 = 120,000 lb-in.

Moment of inertia = 6 x 12 cubed / 12 = 6 x 1,728 / 12 = 864 in^4.

Distance to extreme fiber = 12 / 2 = 6 in.

Section modulus = 864 / 6 = 144 in^3. Check by the direct formula: 6 x 12 squared / 6 = 6 x 144 / 6 = 144 in^3.

Maximum bending stress = 120,000 x 6 / 864 = 720,000 / 864 = 833.3333 psi, displayed as 833.33 psi.

Check by the section modulus form: 120,000 / 144 = 833.3333 psi, the same figure.

Maximum bending stress in ksi = 833.3333 / 1,000 = 0.8333 ksi, displayed as 0.83 ksi.

So the outer fibers carry 833.33 psi, tension at the bottom and compression at the top for a sagging beam, and the stress falls linearly to zero at the neutral axis.

Benefits of Using a Bending Stress Calculator

  • Shows the whole chain, not just the answer: I, S, c and the moment in lb-in are all displayed, so every step of the flexure formula can be checked.
  • Covers the three ways a section is specified: rectangle by dimensions, circle by diameter, and any rolled shape by I and c from the tables.
  • Reports stress in both units: psi for timber work, where allowable values are published in psi, and ksi for steel work.
  • Makes the moment relationship visible: the Compare Moments tab shows stress doubling as the moment doubles, which is the fastest way to judge how much headroom a section has.
  • Catches the unit trap: the moment is entered in lb-ft, as beam moments are usually quoted, and converted to lb-in inside the calculator where the formula needs it.
  • Free and instant: no sign-up, no download, and the results update as you type.

Frequently Asked Questions

What is c and why does it matter?

c is the distance from the neutral axis to the extreme outer fiber of the cross-section, the point farthest from the middle of the beam. Bending stress grows in proportion to distance from the neutral axis, so the extreme fiber carries the highest stress and c is what sets its value. For a symmetric section bent about its strong axis, c is half the overall depth: 6 in for a 12 in deep rectangle, or half the diameter for a circle. For an unsymmetric section the top and bottom fibers sit at different distances from the neutral axis, so the tension and compression stresses differ, and this calculator’s single-c input does not cover that case.

Why is the stress zero at the neutral axis?

Because bending stretches one side of the beam and compresses the other, and the neutral axis is the plane where the material is neither stretched nor compressed. Strain varies linearly with distance from the neutral axis, and in the elastic range stress is strain times E, so stress also varies linearly: maximum tension at one outer surface, maximum compression at the other, and zero in the middle. That is why an I-beam puts most of its material in the flanges, far from the neutral axis, and keeps the web thin: material near the neutral axis carries almost no bending stress.

How do I check an I-beam or channel?

Choose “I-beam or other shape (enter I and c)” and take I and c from the steel section tables, such as the AISC Steel Construction Manual. For a symmetric I-beam bent about its strong axis, use I_x and take c as half the overall depth. For a channel or any unsymmetric shape, the neutral axis is not at mid-depth, so c is the larger of the two distances from the neutral axis to the outer fibers, which the tables give as the section’s centroid location. This calculator reports the single maximum stress; it does not split tension and compression for unsymmetric sections.

What bending stress is too much?

Compare the result with the allowable bending stress for the material. For steel the classic allowable stress design value is Fb = 0.66 x Fy for compact, laterally supported sections: 24 ksi for A36 and 33 ksi for A992. For timber the NDS publishes Fb by species and grade: Douglas Fir-Larch Select Structural is 1,600 psi for beams and stringers and No.2 is 875 psi. This calculator deliberately does not pass or fail the result, because the right allowable value depends on the species, grade, section type, lateral support and code, and picking it is a design decision, not an arithmetic one.

Does the sign of the bending moment matter?

Only for deciding which side is in tension. A sagging moment, the usual case for a beam carrying downward load, puts the bottom fibers in tension and the top fibers in compression. A hogging moment, over a support of a continuous beam, reverses them. The magnitude of the maximum stress is the same either way for a symmetric section, which is why the calculator takes the moment as a positive number and reports the magnitude. For materials that are weaker in tension than in compression, such as unreinforced concrete, the sign matters a great deal, and this calculator is not the right tool for that check.

Disclaimer

This calculator gives estimates of the maximum bending stress at one cross-section, using the Euler-Bernoulli flexure formula, based on the values you enter. It assumes plane sections remain plane, the material stays linearly elastic, the beam is prismatic, and the load acts in a plane of symmetry. It reports the extreme-fiber stress magnitude only: it does not split tension and compression for unsymmetric sections, and it does not check shear stress, deflection, lateral-torsional buckling, bearing or connections. Allowable stress values vary by species, grade, section type, lateral support and code. The results are for planning and estimating only and are not a substitute for a design by a licensed engineer.

ADVERTISEMENT

ADVERTISEMENT