A pipe run can hold far more liquid than it looks like from the outside: 100 feet of 4 inch pipe holds over 65 gallons, enough to flood a room if you cut into it unprepared. This free pipe volume calculator works out exactly how much liquid a pipe holds from its inside diameter and length. Enter the two measurements and it shows the capacity in cubic feet, cubic yards, US gallons and liters, plus the gallons per foot, with a comparison table for common pipe diameters.
Enter the inside diameter (the bore), not the outside diameter or the nominal trade size. Inside diameter equals outside diameter minus twice the wall thickness. For a rough estimate the nominal size is close, but for exact work use the inside diameter from the pipe schedule or the manufacturer's data sheet.
Please enter values above 0 for inside diameter and length.
| Inside Diameter | Volume (cubic feet) | Volume (gallons) | Volume (liters) |
|---|
Each row uses the length entered above, at a different inside diameter. Volume grows with the square of the diameter, so a 6 inch pipe holds nine times as much per foot as a 2 inch pipe.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
Pipe volume is the internal capacity of a pipe, the amount of liquid it holds when completely full. A pipe is a cylinder, so its volume is the area of the circular cross-section multiplied by the length: V = pi x r squared x L, where r is the inside radius and L is the length. The key measurement is the inside diameter (the bore), not the outside diameter or the nominal trade size printed on the pipe. Nominal sizes are historical labels that exist so fittings line up, and the real bore is smaller by twice the wall thickness: inside diameter equals outside diameter minus twice the wall thickness. A nominal 4 inch Schedule 40 pipe, for example, has an actual inside diameter of 4.026 inches.
Knowing pipe volume matters whenever liquid moves through or sits in a pipe: draining a run before cutting into it, flushing a system before water sampling, dosing chemicals into a boiler or hydronic loop by system volume, sizing an expansion tank, or working out how long it takes to fill a new system. If you need the weight of the pipe material itself rather than the liquid inside it, the Pipe Weight Calculator works that out from the pipe dimensions and material.
Radius in feet = inside diameter (in) / 12 / 2
Cross-sectional area (sq ft) = pi x radius squared
Volume (cu ft) = cross-sectional area (sq ft) x length (ft)
Volume (cu yd) = volume (cu ft) / 27
Volume (gallons) = volume (cu ft) x 7.48052
Volume (liters) = volume (gallons) x 3.78541
Gallons per foot = volume (gallons) / length (ft)
The same formula can be written with the full diameter instead of the radius: V = (pi / 4) x D squared x L. The conversion factors are exact definitions, not rounded estimates: one US gallon is exactly 231 cubic inches and one cubic foot is 1,728 cubic inches, so one cubic foot is 1,728 / 231 = 7.48052 US gallons. One US gallon is 3.78541 liters, so the liter figure comes from gallons x 3.78541. A handy shortcut for estimating in your head is gallons per foot = 0.0408 x inside diameter in inches squared, which folds pi, the area formula and the 231 cubic inch gallon into one constant.
A pipe with a 4 inch inside diameter and a 100 foot run. All steps below use the unrounded values; displayed figures are rounded to two decimals only at the end.
Diameter in feet = 4 / 12 = 0.333333 ft.
Radius = 0.333333 / 2 = 0.166667 ft.
Cross-sectional area = pi x 0.166667 squared = 0.087266 sq ft.
Volume = 0.087266 x 100 = 8.726646 cu ft, displayed as 8.73 cu ft.
Volume in cubic yards = 8.726646 / 27 = 0.323209 cu yd, displayed as 0.32 cu yd.
Volume in gallons = 8.726646 x 7.48052 = 65.279852 gallons, displayed as 65.28 gallons.
Volume in liters = 65.279852 x 3.78541 = 247.111005 liters, displayed as 247.11 liters.
Gallons per foot = 65.279852 / 100 = 0.652799 gal/ft, displayed as 0.65 gal/ft.
So the run holds 65.28 gallons (247.11 liters) of liquid when full. That matches the published reference figure of 0.653 gallons per foot for 4 inch pipe, or 65.3 gallons per 100 feet.
Use the inside diameter whenever you can. Nominal pipe size is a trade label, not a measurement: it exists so pipes and fittings from different makers line up, and it does not equal either the inside or the outside diameter. The inside diameter is the outside diameter minus twice the wall thickness, and wall thickness varies by schedule, so the same nominal size can have different bores. A nominal 4 inch Schedule 40 pipe has an actual inside diameter of 4.026 inches and holds about 1.3 percent more than a true 4.000 inch bore would. For rough estimates the nominal size is close enough, within a few percent; for dosing, commissioning or billing, use the real bore from the pipe schedule or data sheet.
It depends on the diameter, and the volume grows with the square of the bore. Using the inside diameter as entered, 100 feet holds about 4.08 gallons at 1 inch, 16.32 gallons at 2 inches, 36.72 gallons at 3 inches, 65.28 gallons at 4 inches and 146.88 gallons at 6 inches. A 6 inch pipe therefore holds nine times as much per foot as a 2 inch pipe, even though the diameter is only three times larger. The Compare Diameters tab in the calculator shows these figures for any length you enter.
Yes. Gallons per foot equals 0.0408 times the inside diameter in inches squared. So a 2 inch bore holds about 0.0408 x 4 = 0.16 gallons per foot, and a 4 inch bore holds about 0.0408 x 16 = 0.65 gallons per foot. The constant folds pi, the circle area formula and the 231 cubic inch gallon into one number, and it reproduces the full calculation to within rounding. Multiply the result by the run length in feet for the total gallons.
Because the volume depends on the cross-sectional area, and area depends on the radius squared. Double the diameter and the radius doubles too, so the area becomes two squared, or four times larger, and the volume follows. This is why upsizing a pipe is such a powerful way to add capacity, and why a small error in the diameter measurement has an outsized effect on the result: measure the bore carefully, because a 10 percent error in diameter becomes roughly a 21 percent error in volume.
This calculator assumes the pipe is completely full, which is the right figure for draining, flushing, filling and dosing, since those jobs deal with the full contents. For a horizontal pipe that is exactly half full, the liquid volume is half the full capacity. For other fill levels the wetted cross-section is a circular segment, which needs a different formula, and for a vertical pipe the liquid depth is simply the height of the liquid column, so volume is the cross-sectional area times that height rather than times the full length.
This calculator gives the internal volume of a uniform, round pipe that is completely full, based on the inside diameter and length you enter. Real pipes vary: the actual bore depends on the schedule and the manufacturer, and using the nominal size instead of the measured inside diameter can shift the result by a few percent. Fittings, valves, bends and connected equipment add volume that this calculator does not count, and partially full pipes hold less than the full capacity shown here. Use the figures for planning, estimating and dosing preparation, and confirm critical volumes against the manufacturer’s data for your specific pipe. This tool is for estimating only and is not a substitute for professional engineering advice.
ADVERTISEMENT
ADVERTISEMENT