Fire Flow Calculator

When firefighters open a hydrant, the number that matters is how many gallons per minute it can deliver, and the only way to know is to measure it. A hydrant flow test does exactly that: water is flowed from an outlet, a pitot gauge reads the pressure of the moving stream, and the reading is converted into a flow rate. This free fire flow calculator does that conversion for you. Enter the outlet diameter, the pitot pressure and the discharge coefficient for the outlet, and it shows the flow in gallons per minute and liters per minute, the stream velocity, and the NFPA 291 hydrant class, with a comparison table for different pitot pressures.

Hydrant Outlet

Measure the inside diameter of the outlet you flowed; most hydrant hose outlets are 2.5 inches. Pick the coefficient that matches the shape of the outlet opening, or the equipment fitted to it. The coefficient matters: a wrong one shifts the result by 10 percent or more.

Pitot Pressure

Enter the pitot gauge reading taken at the center of the flowing stream, about half an outlet diameter out from the port. This is the velocity pressure of the stream, not the static or residual pressure in the main.

Fire flow from this outlet
Flow rate
Flow rate
Flow rate
Stream velocity
NFPA 291 hydrant class
Note: this is the flow from one outlet. If more than one outlet was flowed, calculate each outlet separately and add the flows together for the total. For a pumper outlet (4 inches or larger) NFPA 291 applies an extra correction factor of 0.83 to 0.97 depending on the pitot pressure, so treat the figure for a large outlet as approximate. The flow available at 20 psi residual pressure, which is the number water systems and fire ratings use, is a separate Hazen-Williams step that also needs the static and residual pressures from the test.
Pitot PressureFlow (gpm)Flow (L/min)Stream Velocity (ft/s)

Each row uses the outlet diameter and discharge coefficient entered above, at a different pitot pressure. Flow grows with the square root of pressure, so doubling the pressure raises the flow by about 41 percent, not double.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

What is a Fire Flow Calculator?

A fire flow calculator turns the readings from a hydrant flow test into a flow rate in gallons per minute (gpm). During a flow test, one or more hydrant outlets are opened and a pitot gauge measures the velocity pressure of each stream. The pitot gauge does not read flow directly; it reads pressure, and the flow follows from the pressure, the size of the opening, and how cleanly the water leaves it. That is what the formula below does, and it is the method in NFPA 291, Recommended Practice for Fire Flow Testing and Marking of Hydrants.

The term fire flow has a second meaning worth knowing, so you use the right tool. The ISO Needed Fire Flow is an estimate of how much water a particular building would need in a fire, based on its construction type, floor area, occupancy and nearby exposures. It answers the question “how much water does this building need?” This calculator answers the other question: “how much water does this hydrant deliver?” A water system is adequate where the delivered flow meets or exceeds the needed flow, and comparing the two is how communities rate their fire protection.

How to Use the Fire Flow Calculator

  1. Measure the inside diameter of the hydrant outlet you flowed, in inches, and enter it. Most hydrant hose outlets are 2.5 inches; a pumper outlet is 4 inches or larger.
  2. Pick the discharge coefficient that matches the outlet. A smooth and rounded opening is 0.90, a square and sharp-edged opening is 0.80, and a square opening that projects into the barrel is 0.70. If you used a stream straightener, use 0.95; with a diffuser, use 1.00 unless the manufacturer states a different figure.
  3. Enter the pitot pressure in psi, read at the center of the flowing stream about half an outlet diameter out from the port. This is the velocity pressure of the stream, not the static or residual pressure in the main.
  4. Click Calculate, or just type: the results update as you enter the numbers.
  5. Read the Summary tab for the flow in gpm, L/min and cubic feet per minute, the stream velocity, and the NFPA 291 hydrant class for the flow.
  6. Open the Compare Pitot Pressures tab to see how the flow changes at 20, 30, 40, 50, 60 and 80 psi for the same outlet and coefficient.

Formula

Flow in gpm = 29.84 x c x d^2 x square root of p

Flow in L/min = flow in gpm x 3.78541

Flow in cubic feet per minute = flow in gpm / 7.48052

Stream velocity in ft/s = flow in cubic feet per second / outlet area in square feet

In the main formula, c is the discharge coefficient, d is the outlet diameter in inches, and p is the pitot pressure in psi. The constant 29.84 comes from the physics of water velocity and pressure plus the unit conversions that keep the answer in gallons per minute; it is the value published in NFPA 291. A few references print 29.83 instead, and the difference changes the result by about 0.03 percent, which is far smaller than the error from a wrong coefficient.

The diameter is squared because flow depends on the area of the opening, and area grows with the square of the diameter. The pressure sits under a square root because water velocity grows with the square root of pressure: doubling the pitot pressure raises the flow by about 41 percent, not double. That is why the coefficient and the diameter matter more than small pressure differences; a wrong coefficient shifts the result by 10 percent or more, and a 2.5 inch outlet flows much less than a 4.5 inch outlet at the same pressure.

Two things this calculator does not do, by design. First, if more than one outlet was flowed, calculate each outlet separately and add the flows together for the total. Second, the flow available at 20 psi residual pressure, which is the figure water systems and fire ratings use, is a separate Hazen-Williams step that also needs the static and residual pressures from the test: flow at 20 psi = test flow x ((static pressure minus 20) / (static pressure minus residual pressure)) ^ 0.54. For a pumper outlet (4 inches or larger) NFPA 291 also applies an extra correction factor of 0.83 to 0.97 depending on the pitot pressure, so treat the figure for a large outlet as approximate.

Worked Example

A hydrant with a 2.5 inch smooth, rounded outlet (coefficient 0.90) and a pitot reading of 50 psi. All steps below use the unrounded values; displayed figures are rounded to two decimals only at the end.

Diameter squared = 2.5 x 2.5 = 6.25 sq in.

Square root of the pitot pressure = square root of 50 = 7.07106781.

Flow = 29.84 x 0.90 x 6.25 x 7.07106781 = 1,186.87873 gpm, displayed as 1,186.88 gpm.

Flow in liters per minute = 1,186.87873 x 3.78541 = 4,492.8226 L/min, displayed as 4,492.82 L/min.

Flow in cubic feet per minute = 1,186.87873 / 7.48052 = 158.6626 cu ft/min, displayed as 158.66 cu ft/min.

Outlet area = 3.14159265 x (2.5 / 24)^2 = 0.0340885 sq ft.

Flow in cubic feet per second = 158.6626 / 60 = 2.6443767 cu ft/s.

Stream velocity = 2.6443767 / 0.0340885 = 77.5739 ft/s, displayed as 77.57 ft/s.

So the outlet flows 1,186.88 gpm, which puts the hydrant in the Green class (1,000 to 1,499 gpm) under NFPA 291. As a check on the method, the City of Temecula publishes a worked example with the same 2.5 inch outlet and 0.90 coefficient at 23 psi pitot pressure, giving 804 gpm; this calculator gives 804.98 gpm for those inputs, the difference being Temecula’s rounding to whole gallons.

Benefits of Using a Fire Flow Calculator

  • Converts a pitot reading in seconds: turn a gauge reading into a flow rate without looking up discharge tables.
  • Uses the NFPA 291 method: the formula and the coefficient values come from the standard fire services use for flow testing, not a rough rule of thumb.
  • Shows the flow three ways: gallons per minute, liters per minute and cubic feet per minute, so the figure matches whichever unit your report or system uses.
  • Adds the stream velocity: useful for checking whether the flow is realistic and for downstream hydraulic checks.
  • Gives the hydrant class at a glance: the NFPA 291 color class (Red, Orange, Green or Blue) tells you how the hydrant is marked and rated.
  • Compares pressures side by side: the Compare Pitot Pressures tab shows how the flow changes from 20 to 80 psi, which makes the square-root relationship easy to see.
  • Free and instant: no sign-up, no download, and the results update as you type.

Frequently Asked Questions

What is a fire hydrant flow test?

A flow test measures how much water a hydrant and the water main behind it can deliver. At least two hydrants are used: one is flowed while a gauge on a second, nearby hydrant records the static pressure (no flow) and the residual pressure (during flow), and a pitot gauge measures the velocity pressure of each flowing stream. The pitot reading, outlet diameter and discharge coefficient give the flow in gpm through the NFPA 291 formula, and the static and residual readings are then used to work out the flow available at 20 psi residual pressure. NFPA recommends public hydrants be flow tested every five years and inspected at least annually.

What discharge coefficient should I use?

Look at the shape of the outlet opening. A smooth and rounded opening has a coefficient of 0.90, a square and sharp-edged opening 0.80, and a square opening that projects into the barrel 0.70. These are the NFPA 291 values for a bare port measured with a hand-held pitot gauge. If you fitted a stream straightener, use 0.95; with a diffuser, use 1.00 unless the manufacturer states a different coefficient for the device. Using the wrong coefficient is one of the most common flow test errors, and it shifts the result by 10 percent or more.

Why does the flow use the square root of the pressure?

Because water velocity grows with the square root of pressure, not in proportion to it. The pitot gauge reads velocity pressure, and the velocity of the stream is proportional to the square root of that pressure. Flow is velocity times area, so the square root carries through into the flow formula. In practice this means doubling the pitot pressure raises the flow by about 41 percent, and a small error in the pressure reading has a smaller effect on the flow than the same percentage error in the diameter, which is squared.

What is the flow at 20 psi residual pressure, and why does it matter?

It is the flow the water system can deliver while holding 20 psi of residual pressure in the main, and it is the standard figure for rating hydrants and water systems, because 20 psi is the minimum pressure fire protection systems are designed around. It is calculated from the test flow and the static and residual pressures with a Hazen-Williams formula: flow at 20 psi = test flow x ((static pressure minus 20) / (static pressure minus residual pressure)) ^ 0.54. This calculator gives the test flow; you need the static and residual readings from the same test to take the extra step.

What do the hydrant colors mean?

Under NFPA 291, hydrants are color-coded by their rated flow so firefighters can judge capacity at a glance. Red means under 500 gpm, Orange means 500 to 999 gpm, Green means 1,000 to 1,499 gpm, and Blue means 1,500 gpm or more. The color is usually applied to the hydrant bonnet and caps, and it is based on the flow available at 20 psi residual pressure from a proper flow test, not on a single pitot reading alone.

Disclaimer

This calculator gives the flow from a single hydrant outlet using the NFPA 291 formula and the discharge coefficient you select. The result is only as accurate as the pitot reading, the measured outlet diameter and the coefficient chosen; a wrong coefficient or a misread gauge can shift the figure by 10 percent or more. For a pumper outlet (4 inches or larger) NFPA 291 applies an extra correction factor, so treat the figure for a large outlet as approximate. The flow available at 20 psi residual pressure, which is the figure used for hydrant ratings and fire protection design, needs the static and residual pressures from the test and is not calculated here. Hydrant flow testing should be carried out by trained personnel in coordination with the water department. This tool is for planning and estimating only and is not a substitute for a proper flow test or professional fire protection engineering advice.

ADVERTISEMENT

ADVERTISEMENT