Thread pitch is given two different ways depending on where the fastener comes from: millimetres between crests for metric threads, threads per inch for inch threads. This free thread pitch calculator converts between the two in either direction, and then goes a step further: enter a pitch you measured off a bolt and it matches it against standard metric, UNC and UNF threads, so you can work out what you are holding.
Enter the threads per inch from the designation (20 for 1/4-20 UNC), or a pitch you measured. To measure a pitch, count 10 thread crests with calipers, measure the distance across them and divide by 10: measuring across 10 threads is ten times more accurate than measuring one gap.
Please enter a value above 0.
| Thread Size | Pitch (mm) | Pitch (in) | TPI |
|---|
Pitch and TPI for ten common thread sizes. Metric sizes are listed by their standard coarse pitch; inch sizes by their standard UNC or UNF threads per inch. Note how a 1.5 mm pitch (M10 coarse) and a 16 TPI pitch (3/8-16 UNC, 1.5875 mm) are close but not the same: the two threads do not interchange.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
Thread pitch is given two different ways depending on where the fastener comes from: millimetres between crests for metric threads, threads per inch for inch threads. This free thread pitch calculator converts between the two in either direction, and then goes a step further: enter a pitch you measured off a bolt and it matches it against standard metric, UNC and UNF threads, so you can work out what you are holding. The Compare Sizes tab lists the pitch and TPI of ten common thread sizes side by side, which makes the near-misses easy to spot: a 1.5 mm pitch and a 16 TPI pitch look close on paper, but they are not the same thread.
Thread pitch is the distance between corresponding points on adjacent thread crests, measured along the axis of the bolt. On a metric thread it is written directly in millimetres: an M10 x 1.5 thread has a pitch of 1.5 mm. On a Unified inch thread it is written as threads per inch (TPI), the number of crests in one inch of thread: a 1/4-20 UNC thread has 20 threads per inch, which is a pitch of 1/20 inch, or 0.0500 in. The two are the same measurement expressed differently, and the conversion is exact: pitch in inches is 1 divided by TPI, and pitch in millimetres is 25.4 divided by TPI.
Pitch is also the key to identifying an unknown thread. Measure the pitch, measure the major diameter, and the designation usually follows: a 10 mm bolt with a 1.5 mm pitch is M10 x 1.5, and a 1/4 in bolt with 20 TPI is 1/4-20 UNC. But pitch alone is never enough, because several sizes share the same pitch. The 20 TPI pitch belongs to 1/4-20 UNC, 7/16-20 UNF and 1/2-20 UNF alike, and the 1.5 mm pitch belongs to both M10 x 1.5 and M12 x 1.5. That is why this calculator shows the three nearest standard threads for any pitch you enter, and why you should always measure the diameter too before ordering a tap or a nut.
Once you know the thread, the Pitch Diameter Calculator works out the pitch diameter and minor diameter from the major diameter and pitch, and the Thread Calculator gives the full dimensions, tap drill and clearance hole for the size. If the bolt passes through a part instead of threading into it, the Clearance Hole Calculator sizes the hole it passes through.
Pitch (in) = 1 / TPI
Pitch (mm) = 25.4 / TPI
Threads per inch = 25.4 / pitch (mm)
Threads per inch = 1 / pitch (in)
Measured pitch = measured length over 10 thread gaps / 10
The conversions are exact, because they only restate the same spacing in different units. One inch is exactly 25.4 mm, so a thread with 20 crests in an inch has a pitch of 1/20 in, which is 0.05 in, and 25.4/20 mm, which is 1.27 mm. Going the other way, a 1.5 mm pitch gives 25.4/1.5 = 16.9333 threads per inch, which is why metric pitches rarely convert to whole-number TPI values.
The nearest-match list compares your pitch against 27 standard threads: 15 metric coarse and fine pitches from M3 x 0.5 to M20 x 2.5, and 12 UNC and UNF threads from 1/4-20 to 3/4-16. A match counts as exact when the standard pitch is within 0.005 mm of yours. Anything further away is shown with its difference in millimetres and whether the standard thread is coarser or finer than your measurement.
A thread with 20 threads per inch. All steps below use the unrounded values; displayed figures are rounded to three decimals (mm), four decimals (in) or two decimals (TPI) only at the end.
Pitch in inches = 1 / 20 = 0.0500 in.
Pitch in millimetres = 25.4 / 20 = 1.27 mm exactly.
Threads per inch = 20.00 TPI.
Nearest standard threads, all exact matches at 1.270 mm: 1/4-20 UNC, 7/16-20 UNF and 1/2-20 UNF. All three share the 20 TPI pitch, so the major diameter is what tells them apart: measure it to find which one you have.
Second example, a measured pitch of 1.5 mm: TPI = 25.4 / 1.5 = 16.9333, displayed as 16.93 TPI. Nearest standard threads: M10 x 1.5 (1.500 mm, exact match) and M12 x 1.5 (1.500 mm, exact match), then 3/8-16 UNC at 1.5875 mm, which is 0.0875 mm coarser (displayed as 0.087 mm). The 16 TPI thread is close to the 1.5 mm pitch but it is not the same thread, and a 3/8-16 nut will not fit an M10 x 1.5 bolt.
Use calipers and count 10 threads. Close the caliper jaws on the first crest, open them to the eleventh crest (which is 10 gaps along), read the distance and divide by 10. For a 1.5 mm pitch the calipers read 15 mm over 10 gaps; for a 20 TPI thread they read 0.5 in. Measuring across 10 threads divides your reading error by 10, which matters because a single pitch is only about a millimetre and a small error can point at the wrong standard thread. A thread pitch gauge is quicker and more reliable if you have one: try the blades until one seats cleanly in the grooves with no light showing through.
Because pitch and diameter are independent choices in the thread standards. The standards reuse a small set of pitches across many diameters: 20 TPI is the coarse pitch for 1/4 in and the fine pitch for 7/16 in and 1/2 in, and 1.5 mm is the coarse pitch for M10 and a fine pitch for M12. That is normal, and it is why a pitch measurement alone never identifies a thread. Always measure the major diameter across the crests as well: the pitch plus the diameter together give the designation.
No. A 16 TPI thread has a pitch of 25.4 / 16 = 1.5875 mm, which is 0.0875 mm coarser than a 1.5 mm pitch. The two are close enough to look alike at a glance and to start threading together by hand, but they bind after a turn or two and will damage each other if forced. M10 x 1.5 and 3/8-16 UNC are one of the most common mix-ups in the workshop, because the diameters are close too (10 mm against 9.525 mm). Check both the pitch and the diameter before assuming a metric nut fits an inch bolt.
Pitch is the distance between adjacent thread crests. Lead is the distance the thread advances in one full turn. On a single-start thread, which is what almost every bolt and screw is, the lead equals the pitch: one turn moves the nut one pitch along the bolt. On a multi-start thread, the lead is the pitch times the number of starts: a two-start thread with a 1.5 mm pitch has a 3 mm lead, so the nut moves 3 mm per turn. This calculator assumes single-start threads, as do the standard designations it matches against.
First, re-measure. Count 10 threads and divide by 10, and check the reading against a second spot on the thread: a worn, damaged or dirty section gives a wrong pitch, and measuring a single gap is easy to get wrong by 0.1 mm or more. If the pitch is real but unusual, the thread may be a special or proprietary size, a Whitworth thread (55 degree profile, still found on old British machinery and pipe fittings), or a pipe thread, which this calculator does not cover. In that case, measure the major diameter and the pitch carefully, try a thread pitch gauge, and compare against a full thread chart before ordering anything.
This calculator converts thread pitch and threads per inch exactly, and matches a pitch against 27 standard ISO metric, UNC and UNF threads. The nearest-match list is a guide to identification, not a guarantee: several sizes share the same pitch, worn or damaged threads measure differently from new ones, and special, Whitworth (55 degree) and pipe threads are not in the list. The results are for reference and general workshop use only. Always measure the major diameter as well as the pitch, and confirm the thread with a pitch gauge or a known nut before ordering a tap, a die or a fastener, or cutting a thread.
ADVERTISEMENT
ADVERTISEMENT