A taper can be described four different ways: as a ratio like 1:20, as taper per foot, as taper per inch, or as an angle, and a drawing, a catalogue and a machinist will often each use a different one. This free taper calculator converts between them all from three measurements.
Enter the large and small end diameters and the length of the tapered section, all in inches. The presets fill in the published dimensions of common Morse and Jacobs tapers: Morse tapers run about 0.6 in per foot (MT2 0.5994, MT3 0.6024, MT5 0.6315 in/ft) and Jacobs JT6 is 0.6229 in/ft. Morse tapers are not all the same angle, so check the specific size.
Please enter values above 0 for both diameters and the length.
| Taper Length (in) | Taper per Foot (in/ft) | Taper Ratio | Included Angle (deg) |
|---|
Each row uses the large and small diameters entered above, at a different taper length. Stretching the same diameter change over a longer length makes the taper gentler: the taper per foot and the included angle both fall.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A taper can be described four different ways: as a ratio like 1:20, as taper per foot, as taper per inch, or as an angle, and a drawing, a catalogue and a machinist will often each use a different one. This free taper calculator converts between them all from three measurements. Enter the large diameter, the small diameter and the taper length, and it gives the taper ratio, the taper per inch, the taper per foot, the half angle and the included angle, with presets for common Morse and Jacobs tapers so a standard tool shank can be checked in one click.
A taper calculator works out the geometry of a tapered shaft or hole from its end diameters and its length. A taper is a gradual change in diameter along a length: the large end and the small end differ by some amount, and that difference spread over the length fixes everything else. The taper per inch is the diameter change per inch of length, the taper per foot is twelve times that, the ratio 1:X says the diameter changes by 1 unit for every X units of length, and the half angle is the angle of one side from the centerline, found with an arctangent.
Tapers matter most in machine tooling. Morse tapers hold drill bits, centers and chucks in lathe tailstocks and drill press quills, and Jacobs tapers mount drill chucks onto arbors. Both are self-holding: their half angles are so shallow, about 1.4 to 1.5 degrees for most Morse sizes, that friction alone grips the shank, which is why a Morse taper needs a drift or knock-out bar to release it. Note that Morse tapers are not all the same angle: the taper per foot runs from 0.5986 in/ft for MT1 to 0.6315 in/ft for MT5, so each size needs its own sleeve or reamer.
Choose a standard taper preset (Morse MT2, MT3 or MT5, or Jacobs JT6) to fill in its published dimensions, or leave Custom dimensions and enter your own.
Enter the large diameter in inches, the small diameter in inches and the taper length in inches. All three must use the same unit.
Click Calculate, or just type: the results update as you enter the numbers.
Read the Summary tab for the diameter change, the taper per inch, the taper per foot, the taper ratio, the half angle and the included angle.
Open the Compare Lengths tab to see how the taper per foot, the ratio and the included angle change when the same diameter change is stretched over 3, 6, 9 and 12 inches of length.
Diameter change (in) = large diameter – small diameter
Taper per inch (in/in) = diameter change / taper length
Taper per foot (in/ft) = 12 x taper per inch
Taper ratio = 1:X, where X = taper length / diameter change
Half angle (degrees) = arctan(diameter change / (2 x taper length)), converted to degrees
Included angle (degrees) = 2 x half angle
Standard taper values used for the presets: Morse MT2, large 0.700 in, small 0.572 in, length 2.5625 in, 0.5994 in/ft; Morse MT3, large 0.938 in, small 0.778 in, length 3.1875 in, 0.6024 in/ft; Morse MT5, large 1.748 in, small 1.475 in, length 5.1875 in, 0.6315 in/ft; Jacobs JT6, large 0.676 in, small 0.6241 in, length 1.00 in, 0.6229 in/ft. The half angle can also be found from the taper per foot alone: half angle = arctan(taper per foot / 24).
A turned taper with a large diameter of 2 inches, a small diameter of 1.5 inches and a taper length of 6 inches. All steps below use the unrounded values; displayed figures are rounded to four decimals for rates and two decimals for angles and the ratio.
Diameter change = 2 – 1.5 = 0.5000 in.
Taper per inch = 0.5 / 6 = 0.0833333, displayed as 0.0833 in/in.
Taper per foot = 12 x 0.0833333 = 1.0000 in/ft.
Ratio X = 6 / 0.5 = 12, so the taper ratio is 1:12.00.
Half angle = arctan(0.5 / (2 x 6)) = arctan(0.0416667) = 2.38594 degrees, displayed as 2.39 deg.
Included angle = 2 x 2.38594 = 4.77189 degrees, displayed as 4.77 deg.
So the taper is 1:12, or 1 inch per foot, with an included angle of 4.77 degrees. As a cross-check, the MT2 preset computes to 0.5994 in/ft against the published 0.5994 in/ft, and the MT5 preset to 0.6315 in/ft against the published 0.6315 in/ft.
Converts between all five taper descriptions at once: ratio, taper per inch, taper per foot, half angle and included angle, so a figure from any drawing or catalogue can be matched.
Checks standard tool tapers in one click: presets for Morse MT2, MT3 and MT5 and Jacobs JT6 with published dimensions.
Shows the angle both ways: the half angle for setting a compound slide or taper attachment, and the included angle for matching a mating part.
Compares lengths side by side: the Compare Lengths tab shows how stretching the same diameter change over a longer length makes the taper gentler.
Works in inches throughout: the unit machine taper tables use, with no unit conversion to trip over.
Free and instant: no sign-up, no download, and the results update as you type.
Taper per foot is the change in diameter over 12 inches of length, and taper per inch is the change over 1 inch, so taper per foot is exactly 12 times taper per inch. Machine taper tables usually quote taper per foot (Morse tapers are about 0.6 in/ft), while a machinist setting up a lathe often works in taper per inch. This calculator shows both, so either figure can be checked against the other.
It means the diameter changes by 1 unit for every 20 units of length along the taper. A 1:20 taper over 10 inches of length changes diameter by 0.5 inches. Morse tapers are close to 1:20 on diameter (MT2 is 1:20.02), and a 7:24 taper, used on CAT and BT toolholders, is much steeper at 3.5 inches per foot.
Both are used, which is why the calculator shows both. The half angle is the angle of one side from the centerline, and it is the figure taper tables quote as the angle per side (about 1.43 degrees for MT2). The included angle is the full angle between the two sides, twice the half angle. When setting a compound slide to cut a taper, set the half angle; when checking a taper against a mating part, compare the included angle.
Because their half angle is very shallow, about 1.4 to 1.5 degrees. At such a shallow angle the friction between the mating surfaces is stronger than the force trying to push the taper apart, so the shank grips without a drawbar or lock nut. The trade-off is that it takes a sharp tap with a drift to release one. Steeper tapers, like the 7:24 CAT taper at about 8.3 degrees per side, are not self-holding and need a drawbar.
Measure the large and small diameters and the length, enter them here, and compare the taper per foot and half angle against the standard tables. A result near 0.6 in/ft with a half angle near 1.43 degrees points to a Morse taper, and the gauge diameter then fixes the size. A result near 0.5 in/ft points to a Brown and Sharpe taper, and a steep result near 3.5 in/ft points to a 7:24 toolholder taper. Always confirm with the gauge diameter, because several tapers share similar angles.
This calculator computes taper geometry from the dimensions you enter, using the standard taper formulas and published dimensions for the Morse and Jacobs presets. Published taper tables round their dimensions, so a preset may differ from the tabulated taper per foot by a fraction of a thousandth of an inch per foot. For tooling fits, gauging and any safety-critical work, confirm the dimensions against the applicable standard (ISO 296 for Morse tapers) and the tool manufacturer’s data rather than relying on a calculator alone.
ADVERTISEMENT
ADVERTISEMENT