Road Base Calculator

Road base is the crushed aggregate layer that carries the load under a driveway, parking area or road, and ordering the wrong amount is an expensive mistake: too little leaves a thin spot that ruts and cracks, too much leaves a pile of stone you paid to have delivered. This free road base calculator works out exactly how much you need from the size of your project. Enter the length, width and depth of the area, plus the price per ton your supplier charges, and it shows the area, the volume in cubic feet and cubic yards, the weight in tons and the estimated cost, with a comparison table for different depths.

Project Dimensions

Measure the length and width of the area in feet. Enter the finished depth after compaction; a driveway base is usually 4 to 6 inches deep, while a road or heavy-use base is often 8 to 12 inches.

Price

Enter the price your supplier charges per ton, including delivery if it is priced that way. Delivered full-truck prices in Florida ranged from about $41 to $53 per ton in November 2026; prices vary by region and load size.

Road base needed
Area
Volume
Volume
Weight (at 1.5 tons per cubic yard)
Estimated cost
Estimated cost
Cost per square foot
Note: weight uses 1.5 tons per cubic yard, a typical loose density for road base (crusher run). Published figures range from about 1.40 to 1.60 tons per cubic yard depending on the stone and its moisture, and compacted base weighs more per cubic yard. Road base also loses volume when compacted, so order roughly 10 to 25 percent extra and confirm the exact tons-per-yard figure with your supplier before you buy.
DepthVolume (cubic yards)Weight (tons)Estimated Cost

Each row uses the length, width and price per ton entered above, at a different finished depth. Weight uses 1.5 tons per cubic yard.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

What is a Road Base Calculator?

Road base is a dense-graded crushed aggregate, usually crushed stone graded down to fine dust, that is spread and compacted to form the structural layer beneath a paved or gravel surface. It is sold under many regional names, including crusher run, dense-graded aggregate (DGA), aggregate base course (ABC), 3/4 inch minus, 21A, CA-6 and Class 5. The mix of stone sizes plus fines is what makes it work: when compacted, the fines fill the gaps between the larger pieces and lock together into a hard, load-bearing platform that spreads the weight of vehicles over the ground below.

A road base calculator takes the dimensions of the area you are building and converts them into the quantities a supplier actually sells: cubic yards of volume and tons of weight. Suppliers usually sell road base by the ton, so the weight figure is the one you order from, while the cubic yard figure is useful for checking how many truckloads the job needs. For a general gravel estimate rather than a base layer, the Gravel Calculator covers other stone types and depths. The Crushed Stone Calculator covers the same crusher run material by stone type if you want to compare densities.

How to Use the Road Base Calculator

  1. Measure the length and width of the area in feet and enter them in the Project Dimensions section. For a driveway, measure the full length and the average width.
  2. Enter the depth in inches. This is the finished depth after compaction, not the loose depth as spread. A driveway base is usually 4 to 6 inches deep; a road or heavy-use base is often 8 to 12 inches.
  3. Enter the road base price per ton from your supplier. If the price is quoted delivered, use the delivered figure so the cost estimate matches your real bill.
  4. Click Calculate, or just type: the results update as you enter the numbers.
  5. Read the Summary tab for the area, volume, weight in tons, estimated cost and cost per square foot.
  6. Open the Compare Depths tab to see how the volume, weight and cost change at 4, 6, 8 and 12 inch depths for the same length, width and price.

Formula

Volume in cubic feet = length (ft) x width (ft) x depth (in) / 12

Volume in cubic yards = volume in cubic feet / 27

Weight in tons = volume in cubic yards x 1.5

Estimated cost = weight in tons x price per ton ($)

Cost per square foot = estimated cost / area (sq ft)

The 1.5 tons per cubic yard figure is the loose density of road base (crusher run) used throughout this calculator. Published loose densities for road base and crusher run range from about 1.40 to 1.60 tons per cubic yard depending on the stone type and moisture, and 1.5 sits in the middle of that range. Compacted base is denser: the Tennessee DOT estimates aggregate base at 2.03 tons per compacted cubic yard, so the tonnage for a finished, compacted layer can be higher than the loose figure. Always confirm the exact tons-per-yard figure with your supplier before ordering, and allow extra material for compaction, as a loose layer loses roughly 10 to 30 percent of its volume when compacted.

Worked Example

A driveway 100 ft long and 12 ft wide with a 6 inch road base layer, at $45 per ton. All steps below use the unrounded values; displayed figures are rounded to two decimals only at the end.

Area = 100 x 12 = 1,200 sq ft.

Depth in feet = 6 / 12 = 0.5 ft.

Volume = 1,200 x 0.5 = 600 cu ft.

Volume in cubic yards = 600 / 27 = 22.2222 cu yd, displayed as 22.22 cu yd.

Weight = 22.2222 x 1.5 = 33.3333 tons, displayed as 33.33 tons.

Estimated cost = 33.3333 x 45 = $1,500.00.

Cost per square foot = 1,500 / 1,200 = $1.25 per sq ft.

So the driveway needs 22.22 cubic yards, or 33.33 tons, of road base, costing about $1,500.00 at $45 per ton. In practice you would round the order up, to 34 tons or a full truckload, and add a compaction allowance on top.

Benefits of Using a Road Base Calculator

  • Orders the right amount: converts your measurements into the tons a supplier sells, so you neither run short mid-job nor pay for stone you do not need.
  • Shows volume both ways: cubic feet and cubic yards, so the figure matches whichever unit your supplier or trucker quotes.
  • Prices the job instantly: enter your supplier’s price per ton and see the total cost and the cost per square foot before you commit.
  • Compares depths side by side: the Compare Depths tab shows what 4, 6, 8 and 12 inch layers cost for the same area, so you can weigh a thicker, longer-lasting base against the extra material.
  • Built on verified densities: the 1.5 tons per cubic yard factor is checked against published supplier and DOT figures, with the loose-versus-compacted difference explained rather than hidden.
  • Free and instant: no sign-up, no download, and the results update as you type.

Frequently Asked Questions

What is road base made of?

Road base is crushed stone graded from pieces up to about 3/4 inch or 2 inches down to fine stone dust, with all sizes in between. The fines are essential: they fill the voids between the larger pieces and bind the layer together when compacted, which is why road base sets into a much harder surface than clean, single-size stone. It is usually made from crushed limestone, granite or recycled concrete, and the exact gradation varies by quarry and region.

How many tons of road base are in a cubic yard?

About 1.5 tons per cubic yard for loose road base (crusher run). Published figures range from about 1.40 to 1.60 tons per cubic yard depending on the stone and its moisture. Compacted base weighs more per cubic yard because the same stone occupies less space: the Tennessee DOT estimates aggregate base at 2.03 tons per compacted cubic yard. This calculator uses 1.5 tons per cubic yard, and you should confirm your supplier’s own figure before ordering.

How deep should a road base layer be?

For a residential driveway, 4 to 6 inches of compacted road base is the usual range. Parking areas and farm tracks often use 6 to 8 inches, and roads or areas carrying heavy vehicles may need 8 to 12 inches. The right depth depends on the soil underneath and the loads the surface will carry: soft or clay soil needs a thicker base than firm, well-drained ground. If in doubt, ask your supplier or a local contractor what depth is standard for your soil and use case. Once the base is in, the Gravel Driveway Calculator works out the gravel for the surface layer on top.

How much extra road base should I order for compaction?

Order roughly 10 to 40 percent more than the finished volume. A loose layer of road base loses a noticeable part of its thickness when compacted, because the fines settle into the voids between stones. Suppliers and DOT guidance agree that about 1.4 cubic yards of loose material compacts down to roughly 1 cubic yard of finished base. Spread the material in lifts of 3 to 4 inches and compact each lift before adding the next, rather than dumping the full depth at once.

How much does road base cost per ton?

Prices vary widely by region, quarry and load size. Delivered full-truck prices in Florida ranged from about $41 to $53 per ton in November 2026, and smaller loads cost more per ton because delivery is spread over fewer tons. The material alone at the quarry is usually cheaper than a delivered price. Get a quote from your local supplier, check whether delivery is included, and enter that per-ton figure into the calculator for an accurate estimate.

Disclaimer

This calculator gives estimates based on the dimensions you enter and a typical loose density of 1.5 tons per cubic yard for road base. Real densities vary by stone type, gradation and moisture, and compacted base weighs more per cubic yard than loose material, so the tonnage and cost shown here are approximate. Always confirm the exact density, price and delivery terms with your supplier before ordering, and allow extra material for compaction and uneven ground. This tool is for planning and estimating only and is not a substitute for professional advice on base depth, drainage or pavement design for your specific site.

ADVERTISEMENT

ADVERTISEMENT