Ordering crushed stone by guesswork usually ends in one of two ways: a short load that leaves part of the driveway bare, or a pile of leftover stone sitting on the lawn. This crushed stone calculator removes the guesswork. Enter the length, width and depth of your area, pick your stone type, and it works out the volume in cubic feet and cubic yards, the weight in tons, and the estimated cost at your price per ton. The Compare tab shows every stone type side by side at your dimensions, so you can see at a glance how the weight and cost change when you switch from #57 stone to crusher run or pea gravel. If you are working with rounded gravel instead of crushed stone, try our gravel calculator too. For a driveway-specific estimate, the Gravel Driveway Calculator works out the tonnage and cost for your exact driveway size.
Measure the area in feet and enter the finished depth in inches. A 4 inch depth is a typical driveway top course; a base layer usually runs 6 inches or more.
Each stone type has its own loose bulk density, so the tons change with the type even when the volume stays the same. Leave the price at 0 to hide the cost estimate.
Please enter values above 0 for length, width and depth.
| Stone Type | Density (lb/yd3) | Tons per yd3 | Tons Needed | Est. Cost |
|---|
All rows use the dimensions and price entered above. Volume is the same for every type; only the weight and cost change with density.
ADVERTISEMENT
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
Crushed stone is rock that has been mechanically broken down and screened into graded sizes, from fine dust up to pieces several inches across. Unlike rounded river gravel, crushed stone has sharp angular faces that lock together under weight, which is why it is the standard choice for driveway bases and top courses, paths, patios, drainage layers and shed pads.
The most common grades are sold by number under the AASHTO size system. #57 stone, nominally 3/4 inch, is the workhorse for driveways and drainage. Crusher run, also called 21A, QP or road base depending on the region, is a mix of crushed stone and fine dust that compacts into a hard, stable surface, making it ideal for base layers. Pea gravel is a small rounded stone, about 3/8 inch, used for paths and play areas. Crushed limestone and decomposed granite are popular regional options for driveways and landscaping.
Because each type has a different bulk density, the same volume can weigh quite differently. One cubic yard of pea gravel weighs about 2,600 lb, while a cubic yard of crusher run weighs about 3,000 lb. That difference matters when you order, because most quarries sell stone by the ton.
The calculator uses the standard volume and weight formulas for bulk aggregate:
Volume (cu ft) = Length (ft) x Width (ft) x (Depth (in) / 12)
Volume (cu yd) = Volume (cu ft) / 27
Weight (tons) = Volume (cu yd) x Density (tons per cu yd)
Weight (lb) = Weight (tons) x 2,000
Estimated cost = Weight (tons) x Price per ton ($)
The density depends on the stone type selected. The calculator uses loose bulk densities: #57 crushed stone 2,750 lb per cu yd (1.375 tons per cu yd), crusher run / 21A 3,000 lb per cu yd (1.50 tons per cu yd), pea gravel 2,600 lb per cu yd (1.30 tons per cu yd), crushed limestone 2,700 lb per cu yd (1.35 tons per cu yd), and decomposed granite 2,800 lb per cu yd (1.40 tons per cu yd). Wet stone can weigh 10 to 15 percent more than these dry figures, and compacted crusher run is heavier still, so treat the result as a planning estimate and confirm the weight with your supplier.
A homeowner is resurfacing a 50 ft long, 12 ft wide driveway with 4 inches of #57 crushed stone at $45 per ton.
Step 1, area: 50 x 12 = 600.00 sq ft.
Step 2, depth in feet: 4 / 12 = 1/3 ft (0.3333 ft).
Step 3, volume in cubic feet: 600 x 1/3 = 200.00 cu ft.
Step 4, volume in cubic yards: 200 / 27 = 7.41 cu yd.
Step 5, weight: 7.4074 cu yd x 1.375 tons per cu yd = 10.19 tons, which is 20,370.37 lb.
Step 6, cost: 10.1852 tons x $45 = $458.33.
So the driveway needs 7.41 cu yd, or 10.19 tons, of #57 stone, costing about $458.33. Adding a 10 percent allowance for compaction and spillage would raise the order to about 11.20 tons.
It depends on the stone type. Pea gravel runs about 1.30 tons per cubic yard, crushed limestone about 1.35, #57 stone about 1.375, decomposed granite about 1.40, and crusher run about 1.50. As a rough rule, most crushed stone weighs 1.3 to 1.5 tons per cubic yard, or 2,600 to 3,000 lb.
A driveway top course of #57 stone is usually 4 inches deep over a compacted base. The base layer itself, typically crusher run, should be 6 to 8 inches deep for cars and light trucks, and deeper for heavy vehicles. Paths and patios usually need 3 to 4 inches, while a French drain needs enough stone to cover the pipe by at least 2 inches on all sides.
#57 stone is clean, uniformly graded crushed stone with no fines, so water drains freely through it. That makes it the right choice for drainage and for a driveway top course. Crusher run contains stone dust and fine particles that fill the gaps and lock together when compacted, forming a hard, stable surface. It is the better base layer, but it drains poorly, so it is a poor choice where water needs to pass through.
Delivered #57 stone typically costs $35 to $60 per ton in the US, depending on the region, the quarry and the delivery distance. Crusher run is usually in a similar range or slightly cheaper, while decorative stone such as pea gravel can cost more. Delivery is often charged separately or built into the per-ton price, so always confirm whether the quoted price includes delivery.
Order 5 to 10 percent extra to cover compaction, uneven ground, spillage and edge loss. Crusher run compacts the most, so allow the higher end of the range for a base layer. For a small project, rounding up to the next whole ton is usually enough, and most suppliers are happy to deliver a rounded quantity.
The results from this calculator are planning estimates, not engineering advice. Stone density varies with the rock source, gradation and moisture content, and wet stone can weigh 10 to 15 percent more than the dry loose bulk densities used here. Compacted crusher run is heavier per cubic yard than loose crusher run. Always confirm the quantity, weight and price with your supplier before ordering, and follow local building codes and your project plans for depth and base requirements.
ADVERTISEMENT
ADVERTISEMENT