Bigger power needs more fuel, and your injectors have to deliver it. If they are too small, the engine runs lean at full throttle; if they are far too big, idle and low-speed fuelling suffer. This free Fuel Injector Flow Rate Calculator works out the flow rate each injector needs for your target horsepower, using your engine’s fuel consumption and a safe duty cycle, so you can pick the right size with confidence.
Please enter valid values: horsepower, injectors and BSFC above 0, and a duty cycle between 1 and 100%.
| Injector Size | Size (cc/min) | Max HP Supported |
|---|
Max HP assumes your BSFC, injector count and duty cycle above, at the standard 43.5 psi (3 bar) rating pressure.
ADVERTISEMENT
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A Fuel Injector Flow Rate Calculator estimates the minimum flow rate each fuel injector must deliver for an engine to reach a target horsepower. You enter the target horsepower, the number of injectors, the engine’s brake specific fuel consumption (BSFC), and the maximum duty cycle you are willing to run, and it returns the required flow per injector in lb/hr and cc/min, plus the next common injector size up.
Sizing injectors is a fuel-mass problem: the engine needs a certain mass of fuel per hour to make the power you want, and the injectors have to deliver it within a duty cycle they can survive.
Total fuel flow (lb/hr) = Target horsepower × BSFC
Flow per injector (lb/hr) = Total fuel flow ÷ (Number of injectors × Max duty cycle as a decimal)
Flow per injector (cc/min) = Flow per injector (lb/hr) × 10.5
The ×10.5 conversion is the standard approximation for gasoline. Injector flow ratings are usually measured at 43.5 psi (3 bar); at a different fuel pressure, flow changes with the square root of the pressure ratio.
You are building a naturally aspirated V8 for 400 crank horsepower, with 8 injectors, a BSFC of 0.50 lb/hp/hr, and an 80% maximum duty cycle.
Step 1: Total fuel flow. 400 × 0.50 = 200.00 lb/hr (2,100.00 cc/min).
Step 2: Flow per injector. 200 ÷ (8 × 0.80) = 200 ÷ 6.4 = 31.25 lb/hr.
Step 3: Convert to cc/min. 31.25 × 10.5 = 328.13 cc/min.
Step 4: Pick a size. The next common size up from 31.25 lb/hr is a 36 lb/hr (378 cc/min) injector. A 36 lb/hr injector supports 36 × 8 × 0.80 ÷ 0.50 = 460.80 HP at these settings, giving comfortable headroom above the 400 HP target.
For a naturally aspirated gasoline engine, 0.45 to 0.50 lb/hp/hr is typical. Forced induction engines run richer and usually need 0.55 to 0.65. E85 needs roughly 1.4 times the gasoline figure. These are starting points for sizing; confirm on a dyno with an air-fuel ratio meter.
An injector is a solenoid valve that needs time to close between pulses. At 100% duty cycle it is held open constantly, so fuel delivery stops being precise and the coil can overheat. Sizing for 80% at peak power leaves headroom for hot days, fuel pressure drop, and tuning changes.
Injector flow ratings are usually measured at 43.5 psi (3 bar). Flow changes with the square root of the pressure ratio, so at 58 psi an injector flows about 15% more than its 43.5 psi rating. Always check the pressure a rating was measured at before comparing sizes.
They describe the same flow in different units: lb/hr is mass flow, cc/min is volume flow. For gasoline, multiply lb/hr by 10.5 to get cc/min. American aftermarket injectors are usually rated in lb/hr, while OEM and European injectors are usually rated in cc/min.
Yes. E85 carries less energy per unit volume than gasoline, so the engine needs roughly 30 to 40% more fuel flow for the same power. Use a BSFC about 1.4 times the gasoline figure, and confirm the injectors and fuel system are ethanol compatible.
This calculator provides estimates for planning purposes only. Actual fuel requirements vary with the engine, tune, air-fuel ratio, fuel type, fuel pressure, and operating conditions. Always confirm injector sizing with your tuner and data logs before buying parts, and check the manufacturer’s rated pressure for the injectors you choose.
ADVERTISEMENT
ADVERTISEMENT