Almost every frame, planter box, trim run and picture frame comes down to one question: what angle do you cut each piece at so the corners close without a gap? This free angle cut calculator answers it two ways.
Polygon mode is for closed shapes built from equal pieces, such as a square frame, a hexagon planter or an octagon window casing. Corner mode is for two pieces meeting at one measured corner, such as trim around a bay window. Enter a whole number of sides from 3 to 360, or a corner angle between 1 and 179 degrees.
The diagram labels update as the inputs change.
Please enter a whole number of sides from 3 to 360.
| Shape | Sides | Cut Angle (deg) | Interior Angle (deg) | Exterior Angle (deg) |
|---|
Each row is a regular polygon with the given number of equal sides. As the side count grows, the cut angle per piece falls and the interior angle rises toward 180 degrees.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
Almost every frame, planter box, trim run and picture frame comes down to one question: what angle do you cut each piece at so the corners close without a gap? This free angle cut calculator answers it two ways. Enter the number of sides for a regular polygon, a square frame, a hexagon planter or an octagon casing, and it gives the cut angle per piece. Or enter a measured corner angle for two pieces meeting at a single corner, and it splits that corner evenly between them. It also shows the saw setting, the interior and exterior angles and the number of pieces, so the figure you dial in on the saw is the one you meant.
An angle cut calculator works out the angle to cut the end of each piece so that two or more pieces meet cleanly at a corner. The classic case is a miter joint: two boards cut at matching angles and joined end to end, like the corners of a picture frame. For a regular polygon, a closed shape with equal sides and equal angles, the cut angle depends only on the number of sides. Walking around any closed shape turns through 360 degrees in total, so each corner turns through 360 divided by the number of sides, and each of the two pieces meeting at that corner takes half of that turn. That is why the cut angle for a regular polygon is 180 divided by the number of sides: 45 degrees for a square, 30 for a hexagon, 22.5 for an octagon.
A single corner works the same way but starts from a measured angle instead of a side count. Two pieces meeting at a corner of angle C each carry half of that corner, so each piece is cut at C divided by 2, measured from the edge of the board. This is the figure to use when the corner is not part of a regular shape, for example trim around a bay window or a splayed garden bed corner.
One trap catches out most beginners: the cut angle and the saw setting are not always the same number. A miter saw scale reads the angle from a square cut, while the cut angle is often quoted from the edge of the board, and the two always add to 90 degrees. They match only at a 90 degree corner, which is why this calculator shows both figures with clear labels. For work centered on the miter saw itself, with a reference table of common polygons, the Miter Angle Calculator covers the same ground from the saw setting side. If the cut runs along the length of a board instead of across its end, that is a taper rather than an angle cut, and the Taper Calculator covers it. For the angled seat cut where a rafter sits on a wall plate, see the Birdsmouth Cut Calculator.
Polygon mode, for a regular polygon with n sides:
Cut angle per piece (degrees) = 180 / n
Interior angle (degrees) = (n – 2) x 180 / n
Exterior angle (degrees) = 360 / n
Half of interior angle (degrees) = interior angle / 2 = 90 – 180 / n
Number of pieces = n
Corner mode, for two pieces meeting at a corner of angle C:
Cut angle per piece (degrees) = C / 2
Saw setting from square (degrees) = 90 – C / 2 = (180 – C) / 2
Interior angle (degrees) = C
Exterior angle (degrees) = 180 – C
Number of pieces = 2
The two angles for a cut always add to 90 degrees: the angle from the board edge plus the angle from a square cut equals a right angle. In polygon mode the cut angle of 180 / n is already the saw setting from square, so the second row shows the angle from the board edge instead. In corner mode the cut angle of C / 2 is the angle from the board edge, so the second row shows the saw setting. A compound cut, where the blade tilts as well as swings, needs a spring angle on top of these figures and is outside what this calculator covers.
A square picture frame, 4 sides, in polygon mode. All steps below use the unrounded values; displayed figures are rounded to two decimals.
Cut angle per piece = 180 / 4 = 45.00 deg.
Interior angle = (4 – 2) x 180 / 4 = 2 x 45 = 90.00 deg.
Exterior angle = 360 / 4 = 90.00 deg.
Half of interior angle = 90 / 2 = 45.00 deg.
Number of pieces = 4.
So each of the 4 pieces is cut at 45 degrees, and the corners close at 90 degrees. At a square corner the two ways of measuring the cut agree, which is why a 45 degree setting works on any saw.
As a second check, a single corner of 120 degrees in corner mode: cut angle per piece = 120 / 2 = 60.00 deg, saw setting from square = 90 – 60 = 30.00 deg, interior angle = 120.00 deg, exterior angle = 180 – 120 = 60.00 deg, 2 pieces. Here the two figures differ, and dialling in 60 degrees on a saw that reads from square would cut the wrong angle: the saw setting is 30 degrees.
They are two ways of measuring the same cut, and they always add to 90 degrees. The cut angle is measured from the edge of the board, and the saw setting is measured from a square cut across the board. Most miter saw scales read from square, so a hexagon needs 30 degrees on the saw even though the angle from the board edge is 60 degrees. The two figures match only at a 90 degree corner, where both are 45 degrees. This calculator shows both, labelled, so there is no guessing about which scale is meant.
22.5 degrees per piece. For a regular polygon the cut angle is 180 divided by the number of sides, and 180 divided by 8 is 22.5. The interior angle of the finished octagon is 135 degrees, and the angle from the board edge is half of that, 67.5 degrees, so make sure the 22.5 degree figure is the one set on the saw. The Compare Angles tab lists the same figures for polygons from 3 to 12 sides.
Measure the actual corner with an angle finder or a bevel gauge, then enter it in corner mode. A corner of 120 degrees needs each piece cut at 60 degrees from the board edge, which is a 30 degree setting on a saw that reads from square. Real walls and frames are rarely exactly square, so measure the corner itself rather than assuming 90 degrees, and make a test cut in scrap before cutting the good stock.
Because walking around any closed shape always turns through 360 degrees in total, and more sides means a smaller turn at each corner. Each corner turns through 360 divided by the number of sides, and each piece takes half of that turn, so the cut angle is 180 divided by the number of sides. A triangle turns 120 degrees per corner and needs a 60 degree cut, while a dodecagon turns only 30 degrees per corner and needs a 15 degree cut. As the side count grows the shape approaches a circle and the cut approaches a square cut.
An angle cut, or miter cut, runs across the width of a board at an angle while the blade stays square to the board face: the end of the board is angled. A bevel cut tilts the blade so the cut runs through the thickness of the board at an angle: the edge of the board is angled. A compound cut combines both, tilting and swinging the blade at once, which is what crown molding needs. This calculator covers flat angle cuts only. For an angled cut along the length of a board, see the Taper Calculator.
This calculator computes angle cut geometry from the numbers you enter, using the standard polygon and corner formulas. It assumes equal pieces meeting at equal angles, and it covers flat cuts only, not compound miter and bevel cuts. Real corners are rarely exact, saws need calibration, and a fraction of a degree shows as a gap on a wide board, so measure the actual corner, check the saw setting against the scale, and make a test cut in scrap before cutting finished stock. For structural framing and load bearing joints, confirm the design against the applicable building code and the advice of a qualified professional rather than relying on a calculator alone.
ADVERTISEMENT
ADVERTISEMENT