Miter Angle Calculator

A miter saw only has one job in frame work: cut each piece at the angle that makes the corners close. This free miter angle calculator gives that angle for any regular polygon or any single corner.

Miter Saw Settings

Polygon mode gives the miter saw setting for a closed frame with equal sides, such as an octagon planter or a hexagon picture frame. Corner mode gives the miter for two pieces meeting at one measured corner. Enter a whole number of sides from 3 to 360, or a corner angle between 1 and 179 degrees.

Miter angle: 22.50 deg width board board Corner: 135.00 deg 8 sides

The diagram labels update as the inputs change.

Miter angles
Miter angle per piece
Angle from board edge
Interior corner angle
Exterior angle
Number of pieces
Note: two angles describe the same cut, the angle from the board edge and the angle from a square cut, and they always add to 90 degrees. In polygon mode the miter angle shown is the saw setting, and the second row is the angle from the board edge. In corner mode the miter angle is the angle from the board edge and the second row is the saw setting. The two match only at a 90 degree corner, so check which scale your saw uses before cutting. Measure real corners with an angle finder, since walls are rarely exactly square, and test on scrap first.
PolygonSidesMiter Angle (deg)Interior Angle (deg)Half of Interior (deg)

A reference table of common regular polygons. The miter angle is the saw setting for each shape: a triangle needs 60 degrees per cut, a square 45, a pentagon 36, a hexagon 30 and an octagon 22.5.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

A miter saw only has one job in frame work: cut each piece at the angle that makes the corners close. This free miter angle calculator gives that angle for any regular polygon or any single corner. Enter the number of sides for a closed frame, a square picture frame, a hexagon planter or an octagon casing, and it gives the saw setting per piece. Or enter a measured corner angle for two pieces meeting at one corner, and it splits that corner evenly. A reference table of common polygons sits on the Compare tab, so the familiar figures, 45 degrees for a square, 30 for a hexagon, 22.5 for an octagon, are always one click away.

What is a Miter Angle Calculator?

A miter angle calculator works out the angle to set a miter saw to when two or more pieces meet at a corner. A miter joint is two boards cut at matching angles and joined end to end, and the angle on the saw is what decides whether the joint closes tight or shows a gap. For a regular polygon, a closed shape with equal sides and equal angles, the miter angle depends only on the number of sides. Walking around any closed shape turns through 360 degrees in total, so each corner turns through 360 divided by the number of sides, and each of the two pieces meeting at that corner takes half of that turn. That is why the miter angle for a regular polygon is 180 divided by the number of sides: 45 degrees for a square frame, 30 for a hexagon, 22.5 for an octagon.

A single corner works the same way but starts from a measured angle instead of a side count. Two pieces meeting at a corner of angle C each carry half of that corner, so each piece is cut at C divided by 2, measured from the edge of the board. This is the figure to use when the corner is not part of a regular shape, for example trim meeting at a bay window or a splayed corner on a garden bed.

The most common mistake is mixing up the two ways of measuring a cut. A miter saw scale reads the angle from a square cut, while the cut is often quoted from the edge of the board, and the two always add to 90 degrees. They match only at a 90 degree corner, which is why this calculator shows both figures with clear labels. For the same geometry framed as a general cutting tool, with polygon and corner modes and a compare tab that follows the mode, see the Angle Cut Calculator. If the angle runs along the length of a board instead of across its end, that is a taper rather than a miter, and the Taper Calculator covers it.

How to Use the Miter Angle Calculator

  1. Choose the calculation mode: Regular polygon for a closed frame with equal sides, or Single corner for two pieces meeting at one measured corner.
  2. In polygon mode, enter the number of sides as a whole number from 3 to 360. In corner mode, enter the corner angle in degrees, between 1 and 179.
  3. Click Calculate, or just type: the results update as you enter the numbers.
  4. Read the Summary tab for the miter angle per piece, the second angle (the angle from the board edge in polygon mode, the saw setting from square in corner mode), the interior corner angle, the exterior angle and the number of pieces. The diagram in the Summary tab updates as the inputs change, so the miter angle and corner angle it shows always match the current numbers.
  5. Open the Common Polygons tab for a reference table of the shapes woodworkers cut most: triangle, square, pentagon, hexagon, heptagon, octagon, nonagon, decagon and dodecagon, each with its miter angle, interior angle and half of the interior angle.

Miter Angle Calculator Formula

Polygon mode, for a regular polygon with n sides:

Miter angle per piece (degrees) = 180 / n

Interior corner angle (degrees) = (n – 2) x 180 / n

Exterior angle (degrees) = 360 / n

Angle from board edge (degrees) = interior angle / 2 = 90 – 180 / n

Number of pieces = n

Corner mode, for two pieces meeting at a corner of angle C:

Miter angle per piece (degrees) = C / 2

Saw setting from square (degrees) = 90 – C / 2 = (180 – C) / 2

Interior corner angle (degrees) = C

Exterior angle (degrees) = 180 – C

Number of pieces = 2

The two angles for a cut always add to 90 degrees: the angle from the board edge plus the angle from a square cut equals a right angle. In polygon mode the miter angle of 180 / n is already the saw setting from square, so the second row shows the angle from the board edge instead. In corner mode the miter angle of C / 2 is the angle from the board edge, so the second row shows the saw setting. A compound cut, where the blade tilts as well as swings, needs a spring angle on top of these figures and is outside what this calculator covers.

Worked Example

An octagon planter box, 8 sides, in polygon mode. All steps below use the unrounded values; displayed figures are rounded to two decimals.

Miter angle per piece = 180 / 8 = 22.50 deg.

Interior corner angle = (8 – 2) x 180 / 8 = 6 x 22.5 = 135.00 deg.

Exterior angle = 360 / 8 = 45.00 deg.

Angle from board edge = 135 / 2 = 67.50 deg.

Number of pieces = 8.

So the saw is set to 22.5 degrees and all 8 pieces are cut the same way, and the corners close at 135 degrees. The figure that matters at the saw is 22.5 degrees, not the 67.5 degree angle from the board edge.

As a second check, a hexagon frame, 6 sides: miter angle = 180 / 6 = 30.00 deg, interior corner angle = (6 – 2) x 180 / 6 = 120.00 deg, exterior angle = 360 / 6 = 60.00 deg, angle from board edge = 120 / 2 = 60.00 deg, 6 pieces. And a single corner of 120 degrees in corner mode: miter angle = 120 / 2 = 60.00 deg, saw setting from square = 90 – 60 = 30.00 deg, interior corner angle = 120.00 deg, exterior angle = 60.00 deg, 2 pieces.

Benefits of Using a Miter Angle Calculator

  • Gives the saw setting directly: the miter angle for a regular polygon is the number to dial in, with no conversion step.
  • Shows both ways of reading the cut, the angle from the board edge and the saw setting from square, so the figure set on the saw matches the scale.
  • Carries a reference table of common polygons on the Compare tab, from a triangle at 60 degrees to a dodecagon at 15 degrees, so familiar shapes need no typing.
  • Handles real corners too: corner mode splits any measured corner from 1 to 179 degrees evenly between two pieces.
  • Gives the full geometry at a glance: miter angle, interior corner angle, exterior angle and piece count, with a live diagram that updates as the inputs change.
  • Free and instant: no sign-up, no download, and the results update as you type.

Frequently Asked Questions

What miter angle do I need for an octagon?

22.5 degrees per piece. For a regular polygon the miter angle is 180 divided by the number of sides, and 180 divided by 8 is 22.5. Set the saw to 22.5 degrees and cut all 8 pieces the same way. The interior corner of the finished octagon is 135 degrees, and the angle from the board edge is half of that, 67.5 degrees, so make sure the 22.5 degree figure is the one set on the saw. The Common Polygons tab lists the same figures for nine common shapes.

What is the difference between the miter angle and the angle on the saw scale?

Usually nothing, but it depends on the mode and on how the saw is marked. For a regular polygon the miter angle of 180 divided by the number of sides is the saw setting from square, which is what most miter saw scales show. For a single corner the miter angle is measured from the board edge, and the saw setting from square is 90 degrees minus that figure. The two ways of measuring always add to 90 degrees and match only at a 90 degree corner. Some older saws and gauges are marked the other way, reading the angle from the board edge, so check which zero the scale uses before cutting.

How do I miter a corner that is not square?

Measure the actual corner with an angle finder or a bevel gauge, then enter it in corner mode. A corner of 120 degrees needs each piece cut at 60 degrees from the board edge, which is a 30 degree setting on a saw that reads from square. A corner that measures 91 degrees instead of 90 needs 45.5 degrees per piece, a 44.5 degree setting on a saw that reads from square, and that half degree shows as a visible gap on the outside of the joint if the corner is assumed square, so measure the corner itself rather than assuming it is square, and make a test cut in scrap before cutting the good stock.

Why is a hexagon 30 degrees and not 60?

Because 60 degrees is the angle from the board edge, not the saw setting. A hexagon has an interior angle of 120 degrees, and half of that is 60 degrees, which is the angle between the cut face and the long edge of the board. The saw setting is measured from a square cut, and the two always add to 90 degrees, so the saw setting is 90 minus 60, which is 30 degrees. The same arithmetic gives 180 divided by 6 directly. A square frame is the one case where the two figures agree, at 45 degrees each.

Can I use this for crown molding?

No, not directly. Crown molding sits against the wall and ceiling at a tilt, so it needs a compound cut: a miter angle and a bevel angle worked out together from the corner angle and the spring angle of the molding. For a standard 90 degree corner with 38 degree spring angle molding, the compound settings are about 31.62 degrees miter and 33.86 degrees bevel, which neither this calculator nor the flat miter formula gives. This calculator covers flat miters, where the work lies flat on the saw table. For a flat mitered frame, a planter or trim, it gives the full answer.

Disclaimer

This calculator computes miter geometry from the numbers you enter, using the standard polygon and corner formulas. It assumes equal pieces meeting at equal angles, and it covers flat miters only, not compound miter and bevel cuts. Real corners are rarely exact, saws need calibration, and a fraction of a degree shows as a gap on a wide board, so measure the actual corner, check the saw setting against the scale, and make a test cut in scrap before cutting finished stock. For structural framing and load bearing joints, confirm the design against the applicable building code and the advice of a qualified professional rather than relying on a calculator alone.

ADVERTISEMENT

ADVERTISEMENT