Please enter a fuel flow above 0 lb/hr and a horsepower above 0.
| Fuel Flow (lb/hr) | BSFC (lb/hp/hr) | BSFC (g/kWh) | Thermal Efficiency |
|---|
Fuel flow levels at the horsepower you entered above. Higher fuel flow at the same power means a higher BSFC and a less efficient engine.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A BSFC Calculator works out brake specific fuel consumption, the mass of fuel an engine burns per unit of power per hour. You enter the fuel flow in lb/hr and the brake horsepower, and it returns the BSFC in lb/hp/hr and in g/kWh, the fuel flow converted to cc/min, and an estimated thermal efficiency for gasoline. Because BSFC is measured per horsepower, it lets you compare the efficiency of engines of any size, from a small four-cylinder to a big-block V8. The same figure is also the starting point for sizing fuel system parts: the Fuel Injector Flow Rate Calculator uses BSFC to work out how much flow each injector must deliver.
BSFC is fuel mass flow divided by power output, both measured at the same operating point.
BSFC (lb/hp/hr) = Fuel flow (lb/hr) / Brake horsepower (hp)
BSFC (g/kWh) = BSFC (lb/hp/hr) x 608.277
Fuel flow (cc/min) = Fuel flow (lb/hr) x 10.5
The x10.5 conversion is the standard approximation for gasoline. The metric conversion factor is exact: 1 lb/hp/hr equals 608.277 g/kWh.
Thermal efficiency (%) = 100 / (BSFC in g/kWh x 0.012222)
The 0.012222 figure is gasoline’s lower heating value in kWh per gram (44 MJ/kg). Thermal efficiency is an estimate for gasoline only; it does not apply to diesel or E85 without their own heating values.
A naturally aspirated V8 burns 150 lb/hr of fuel while making 300 brake horsepower on the dyno.
Step 1: BSFC. 150 / 300 = 0.5000 lb/hp/hr.
Step 2: Metric BSFC. 0.50 x 608.277 = 304.14 g/kWh.
Step 3: Fuel flow in cc/min. 150 x 10.5 = 1,575.00 cc/min.
Step 4: Thermal efficiency. 100 / (304.14 x 0.012222) = 26.90%.
A BSFC of 0.50 lb/hp/hr sits in the normal range for a naturally aspirated gasoline engine, and 26.90% thermal efficiency is a typical result for a port-injected gasoline V8. If the same engine burned 180 lb/hr at 300 hp, its BSFC would rise to 0.60 lb/hp/hr and efficiency would fall to 22.42%, showing a rich tune or a less efficient setup.
For a naturally aspirated gasoline engine, 0.45 to 0.50 lb/hp/hr (about 274 to 304 g/kWh) is typical, and below 0.45 is excellent. Modern turbocharged direct-injection gasoline engines can reach 0.40 to 0.43 at their best point. Forced induction engines usually run richer for safety, at 0.55 to 0.65. If you are adding boost, the Boost Horsepower Calculator can estimate your power gain first.
BSFC varies with load and speed. Engines are usually most efficient near peak torque under moderate load; at full throttle many tunes add extra fuel for cooling and knock safety, which raises BSFC. Always compare BSFC figures measured at the same operating point.
E85 carries less energy per gallon than gasoline, so its BSFC is roughly 1.4 times the gasoline figure, about 0.63 to 0.70 lb/hp/hr. Diesel engines are more efficient than gasoline engines and typically run 0.30 to 0.40 lb/hp/hr. The thermal efficiency shown here is for gasoline only.
The accurate way is a fuel flow meter on a dyno, or the fuel flow reading from an engine management system or data logger. A rough estimate from injector size and duty cycle is possible, but it is only as accurate as the injector data and the duty cycle reading.
Lower BSFC means better fuel efficiency at the measured point, but it is not the whole story. An engine tuned very lean can show a low BSFC while risking detonation and engine damage. BSFC is best used alongside air-fuel ratio, power, and knock data, not on its own.
ADVERTISEMENT
ADVERTISEMENT