A flat head screw only sits flush when the countersink is cut to exactly the right depth: too shallow and the head stands proud, too deep and it sinks below the surface and weakens the joint. This free countersink depth calculator finds that depth from three numbers.
Enter the countersink diameter D (the diameter of the cone mouth at the surface, usually the screw head diameter), the hole diameter d (the pilot or clearance hole), and the included angle of the countersink. Use the preset buttons for the common angles: 82 degrees for inch flat head screws, 90 degrees for metric flat head screws, and 100 degrees for aerospace work. The depth is measured from the surface down to where the cone meets the hole.
Please enter diameters above 0, with the countersink diameter larger than the hole diameter, and an angle between 1 and 179 degrees.
| Included Angle (deg) | Depth (in) | Depth (mm) | Depth Factor |
|---|
Each row uses the countersink and hole diameters entered above, at a different included angle. Opening the angle up makes the cone shallower, so the same head diameter needs less depth.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A flat head screw only sits flush when the countersink is cut to exactly the right depth: too shallow and the head stands proud, too deep and it sinks below the surface and weakens the joint. This free countersink depth calculator finds that depth from three numbers.
Enter the countersink diameter, the hole diameter and the included angle, and it gives the depth to cut, in inches and millimetres, with presets for the common 82, 90, 100, 110 and 120 degree countersinks.
A countersink depth calculator works out how deep a conical countersink must be cut so a flat head screw seats flush with the surface. A countersink is a cone cut into the mouth of a drilled hole. The cone runs from the countersink diameter D at the surface down to the hole diameter d, and the included angle of the cone fixes how steeply it narrows. The depth is the axial distance from the surface to where the cone meets the hole wall.
The formula is depth = (D – d) / (2 x tan(angle / 2)). Only the diameter difference matters, because the cone only spans the ring between the hole edge and the head edge, and the tangent of half the angle converts that radial difference into depth. A wider angle needs less depth for the same diameters: at 90 degrees the tangent of 45 degrees is exactly 1, so the depth is exactly half the diameter difference.
The standard angles follow the screw standard: 82 degrees for inch flat head screws (ASME B18.6.3), 90 degrees for metric flat head screws (ISO 7046), and 100 degrees for aerospace work. A #10 inch flat head screw, for example, has a 0.385 in head and a 0.201 in normal clearance hole, giving a depth of 0.1058 in at 82 degrees. The hole diameter itself comes from the screw size: use the Clearance Hole Calculator to find the right clearance hole before working out the countersink depth.
Diameter difference (in) = countersink diameter D – hole diameter d
Half angle (degrees) = included angle / 2
Depth factor = 1 / (2 x tan(half angle))
Countersink depth (in) = diameter difference x depth factor = (D – d) / (2 x tan(angle / 2))
Countersink depth (mm) = depth in inches x 25.4
Depth factors for the common angles: 82 deg 0.5752 (divisor 2 x tan(41 deg) = 1.7386), 90 deg 0.5000 (divisor 2.0000), 100 deg 0.4195 (divisor 2.3835), 110 deg 0.3501, 120 deg 0.2887. The reverse relation is also useful at the machine: at 90 degrees, each extra 0.10 in of depth widens the countersink diameter by 0.20 in, because the diameter grows by twice the depth times tan(45 deg).
A countersink for a 0.5 in head over a 0.25 in hole at 82 degrees. All steps below use the unrounded values; displayed figures are rounded to four decimals for depths and the factor, and two decimals for angles and millimetres.
Diameter difference = 0.5 – 0.25 = 0.2500 in.
Half angle = 82 / 2 = 41.00 deg.
tan(41 deg) = 0.86929, so the divisor is 2 x 0.86929 = 1.73857.
Depth = 0.25 / 1.73857 = 0.1438 in.
Depth in millimetres = 0.1438 x 25.4 = 3.65 mm.
Depth factor = 1 / 1.73857 = 0.5752.
So the countersink should be cut 0.1438 in (3.65 mm) deep for the head to sit flush. As cross-checks, the same diameters at 90 degrees give exactly 0.1250 in (half the diameter difference), and a 12 mm countersink over a 6 mm hole gives 3.451 mm at 82 degrees, 3.000 mm at 90 degrees and 2.517 mm at 100 degrees, matching published worked examples.
Depth = (D – d) / (2 x tan(angle / 2)), where D is the countersink diameter at the surface, d is the hole diameter, and the angle is the included angle of the countersink. For a 0.5 in countersink over a 0.25 in hole at 82 degrees, the depth is (0.5 – 0.25) / (2 x tan(41 deg)) = 0.25 / 1.7386 = 0.1438 in. The angle in the formula is the included angle, not the half angle, so do not halve it before entering it.
Match the angle to the screw standard. Inch flat head screws use an 82 degree countersink (ASME B18.6.3), metric flat head screws use 90 degrees (ISO 7046), and aerospace fasteners commonly use 100 degrees. Using the wrong angle leaves the head sitting on a ring instead of seating on the full cone, which looks wrong and loads the screw unevenly. The preset buttons cover all three, plus 110 and 120 degrees.
No. The depth this calculator gives is measured from the workpiece surface down to where the cone meets the hole wall, which is the depth a depth stop or DRO should be set to. The pointed tip of the tool goes deeper than that, and a tool with a flat or rounded tip has its own offset. Touch off on the surface, then cut to the depth shown here, and check the resulting mouth diameter with a countersink gauge if the fit matters.
Because the depth is the radial difference divided by twice the tangent of half the angle, and the tangent grows as the angle opens up. At 82 degrees the depth factor is 0.5752, at 90 degrees it is 0.5000, and at 120 degrees it is only 0.2887, so the same head diameter needs about half the depth at 120 degrees that it needs at 82 degrees. The Compare Angles tab shows this directly for your diameters.
Drill the clearance hole for the screw first, then countersink into it. The hole diameter is the d in the formula, so a larger hole needs less countersink depth to reach the same head diameter. Use the Clearance Hole Calculator to find the normal clearance hole for your screw size, then enter that diameter here with the head diameter to get the depth.
This calculator computes countersink depth from the dimensions you enter, using the standard cone formula depth = (D – d) / (2 x tan(angle / 2)) for an ideal sharp cone meeting a straight cylindrical hole. Real tools have flat or rounded tips, and real holes have tolerances, burrs and coatings, so the actual mouth diameter can differ slightly from the ideal figure. For flush fits that matter, check the finished countersink with a gauge and confirm the screw head diameter and angle against the fastener standard (ASME B18.6.3 for inch flat heads, ISO 7046 for metric) rather than relying on a calculator alone.
ADVERTISEMENT
ADVERTISEMENT