How fast will your boat actually go? This free Boat Speed Calculator estimates the top speed of a planing powerboat from its horsepower, loaded weight, and hull type using Crouch’s formula, and it also shows the hull speed limit for displacement mode. Enter your waterline length, engine horsepower, total loaded weight, and hull type to get your estimated top speed in knots, mph, and km/h, plus a horsepower comparison table to help you decide whether repowering is worth it.
Please enter a waterline length, horsepower, and boat weight above 0.
| Horsepower | Top Speed (knots) | Top Speed (mph) | Top Speed (km/h) | lb per hp |
|---|
Speeds use the boat weight and hull type you entered above. Hull speed does not change with horsepower.
Founder & CEO, Techraxy
Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.
User Ratings:
ADVERTISEMENT
ADVERTISEMENT
A Boat Speed Calculator estimates how fast a boat can travel using two classic naval architecture formulas. For displacement hulls, such as sailboats and trawlers, the practical top speed is the hull speed, which depends only on waterline length: once the bow wave grows as long as the hull, the boat must climb its own wave and extra power buys very little speed. For planing hulls, such as runabouts and center consoles, the top speed depends on power and weight through Crouch’s formula, a rule of thumb developed by naval architect George Crouch in the early 1900s and still used by boat designers today. This calculator gives you both numbers, so you can see the displacement limit and the planing estimate side by side. If you are also working out the cost of the boat itself, the Boat Loan Calculator can help you estimate monthly payments.
Hull speed (displacement limit), in knots:
Hull speed = 1.34 x square root of waterline length in feet
Crouch’s formula (planing top speed), in knots:
Top speed = C x square root of (horsepower / weight in pounds)
Where C is the Crouch constant for the hull type, from naval architect Dave Gerr’s table (Propeller Handbook). Crouch’s formula technically uses shaft horsepower, about 95 to 96 percent of the engine’s rated horsepower; the calculator treats the figure you enter as shaft horsepower.
Hull type / C (knots) table:
Conversions: 1 knot = 1.15078 mph = 1.852 km/h. Note that the C values above give speed in knots; the equivalent constants for a direct mph result are 1.15 times larger (for example, 172 for an average runabout). The speed-length ratio is the top speed in knots divided by the square root of the waterline length in feet; a ratio above 3.0 indicates planing.
Take a runabout with a 20 ft waterline, a 150 hp engine, a loaded weight of 2,500 lb, and an average runabout hull (C = 150).
Step 1, hull speed: 1.34 x square root of 20 = 1.34 x 4.4721 = 5.99 knots (6.90 mph / 11.10 km/h). This is the practical limit if the boat stayed in displacement mode.
Step 2, planing top speed: 150 x square root of (150 / 2,500) = 150 x square root of 0.06 = 150 x 0.2449 = 36.74 knots.
Step 3, convert: 36.74 knots x 1.15078 = 42.28 mph, and 36.74 knots x 1.852 = 68.05 km/h.
Step 4, power-to-weight: 2,500 / 150 = 16.67 lb per hp. The speed-length ratio is 36.74 / 4.4721 = 8.22, well above 3.0, confirming the boat planes.
Hull speed is the practical top speed of a displacement hull, in knots equal to 1.34 times the square root of the waterline length in feet. At hull speed the bow wave’s wavelength equals the waterline length, so the boat sits in a wave trough and needs disproportionate power to go faster. It is a soft economic limit, not a hard wall, but plan passages at roughly 80 to 90 percent of hull speed.
Crouch’s formula estimates a planing boat’s top speed in knots as C times the square root of horsepower divided by weight in pounds, where C is a hull-type constant from 150 for average runabouts to 230 for racing catamarans. It was developed by naval architect George Crouch and assumes a well-matched propeller of about 50 to 60 percent efficiency. Real results usually fall within about 10 to 15 percent of the estimate.
Use 150 for average runabouts and cruisers, 175 as the normal average for most ordinary boats (Dave Gerr’s recommendation when in doubt), 190 for high-speed runabouts, 210 for race boats, 220 for stepped hydroplanes, and 230 for racing power catamarans and sea sleds. Pick the type closest to your hull; if you are unsure, 175 is the safe choice.
Because speed rises with the square root of the power-to-weight ratio. Doubling the horsepower multiplies speed by the square root of 2, about 1.41, so you gain roughly 41 percent more speed, not 100 percent. The same square-root rule means adding 20 percent more weight cuts speed by about 9 percent.
Only the hull speed part. Sailboats and trawlers are displacement hulls, so their practical top speed is the hull speed shown in the results. Crouch’s formula applies only to planing hulls that rise onto the surface at speed, so ignore the planing estimate for a boat that cannot plane.
This calculator provides estimates for planning purposes only. Crouch’s formula is an empirical rule of thumb, and real top speed depends on propeller selection and condition, trim, load distribution, hull condition, water conditions, and altitude. Results are typically within about 10 to 15 percent of a well-matched planing hull’s actual top speed. Always follow the boat manufacturer’s maximum horsepower rating and local speed regulations, and never exceed safe operating speeds for the conditions.
ADVERTISEMENT
ADVERTISEMENT