Countersink Depth Calculator

A flat head screw only sits flush when the countersink is cut to exactly the right depth: too shallow and the head stands proud, too deep and it sinks below the surface and weakens the joint. This free countersink depth calculator finds that depth from three numbers.

Countersink Dimensions

Enter the countersink diameter D (the diameter of the cone mouth at the surface, usually the screw head diameter), the hole diameter d (the pilot or clearance hole), and the included angle of the countersink. Use the preset buttons for the common angles: 82 degrees for inch flat head screws, 90 degrees for metric flat head screws, and 100 degrees for aerospace work. The depth is measured from the surface down to where the cone meets the hole.

D 0.5000 in Hole d 0.2500 in Included angle 82 deg Depth 0.1438 in
Countersink depth
Diameter difference (D - d)
Half angle
Countersink depth
Countersink depth (mm)
Depth factor 1 / (2 x tan(angle / 2))
Note: the depth is measured from the workpiece surface to where the cone meets the hole wall, not to the tip of the tool. A wider included angle needs less depth for the same diameters: at 90 degrees the depth is exactly half the diameter difference. If your countersink tool has a flat or rounded tip, touch off on the surface and use the depth below the hole edge instead.
Included Angle (deg)Depth (in)Depth (mm)Depth Factor

Each row uses the countersink and hole diameters entered above, at a different included angle. Opening the angle up makes the cone shallower, so the same head diameter needs less depth.

Powered by Techraxy

Creator & Reviewer

Faiq Ur Rahman

Founder & CEO, Techraxy

Faiq Ur Rahman is a web designer, digital product developer, and Founder of Techraxy, a growing platform of online calculators and utility tools. He specializes in building structured, user-friendly tools focused on finance, health, conversions, productivity, and everyday problem-solving. He is passionate about developing practical digital solutions that make complex tasks simpler for users worldwide.

Share:

Rate this Tool

User Ratings:

0
0 out of 5 stars (based on 0 reviews)
Excellent
Very good
Average
Poor
Terrible

ADVERTISEMENT

ADVERTISEMENT

A flat head screw only sits flush when the countersink is cut to exactly the right depth: too shallow and the head stands proud, too deep and it sinks below the surface and weakens the joint. This free countersink depth calculator finds that depth from three numbers.

Enter the countersink diameter, the hole diameter and the included angle, and it gives the depth to cut, in inches and millimetres, with presets for the common 82, 90, 100, 110 and 120 degree countersinks.

What is a Countersink Depth Calculator?

A countersink depth calculator works out how deep a conical countersink must be cut so a flat head screw seats flush with the surface. A countersink is a cone cut into the mouth of a drilled hole. The cone runs from the countersink diameter D at the surface down to the hole diameter d, and the included angle of the cone fixes how steeply it narrows. The depth is the axial distance from the surface to where the cone meets the hole wall.

The formula is depth = (D – d) / (2 x tan(angle / 2)). Only the diameter difference matters, because the cone only spans the ring between the hole edge and the head edge, and the tangent of half the angle converts that radial difference into depth. A wider angle needs less depth for the same diameters: at 90 degrees the tangent of 45 degrees is exactly 1, so the depth is exactly half the diameter difference.

The standard angles follow the screw standard: 82 degrees for inch flat head screws (ASME B18.6.3), 90 degrees for metric flat head screws (ISO 7046), and 100 degrees for aerospace work. A #10 inch flat head screw, for example, has a 0.385 in head and a 0.201 in normal clearance hole, giving a depth of 0.1058 in at 82 degrees. The hole diameter itself comes from the screw size: use the Clearance Hole Calculator to find the right clearance hole before working out the countersink depth.

How to Use the Countersink Depth Calculator

  1. Enter the countersink diameter D in inches. This is the diameter of the cone mouth at the surface, usually the screw head diameter.
  2. Enter the hole diameter d in inches. This is the pilot or clearance hole the cone grows out of.
  3. Enter the included angle in degrees, or tap a preset button: 82 deg for inch flat head screws, 90 deg for metric flat head screws, 100 deg for aerospace, or 110 or 120 deg.
  4. Click Calculate, or just type: the results update as you enter the numbers. The diagram updates as the inputs change, showing the cone cross-section with the live diameters, angle and depth.
  5. Read the Summary tab for the diameter difference, the half angle, the depth factor, and the countersink depth in inches and millimetres.
  6. Open the Compare Angles tab to see how the depth changes across 82, 90, 100, 110 and 120 degrees for the same two diameters.

Countersink Depth Calculator Formula

Diameter difference (in) = countersink diameter D – hole diameter d

Half angle (degrees) = included angle / 2

Depth factor = 1 / (2 x tan(half angle))

Countersink depth (in) = diameter difference x depth factor = (D – d) / (2 x tan(angle / 2))

Countersink depth (mm) = depth in inches x 25.4

Depth factors for the common angles: 82 deg 0.5752 (divisor 2 x tan(41 deg) = 1.7386), 90 deg 0.5000 (divisor 2.0000), 100 deg 0.4195 (divisor 2.3835), 110 deg 0.3501, 120 deg 0.2887. The reverse relation is also useful at the machine: at 90 degrees, each extra 0.10 in of depth widens the countersink diameter by 0.20 in, because the diameter grows by twice the depth times tan(45 deg).

Worked Example

A countersink for a 0.5 in head over a 0.25 in hole at 82 degrees. All steps below use the unrounded values; displayed figures are rounded to four decimals for depths and the factor, and two decimals for angles and millimetres.

Diameter difference = 0.5 – 0.25 = 0.2500 in.

Half angle = 82 / 2 = 41.00 deg.

tan(41 deg) = 0.86929, so the divisor is 2 x 0.86929 = 1.73857.

Depth = 0.25 / 1.73857 = 0.1438 in.

Depth in millimetres = 0.1438 x 25.4 = 3.65 mm.

Depth factor = 1 / 1.73857 = 0.5752.

So the countersink should be cut 0.1438 in (3.65 mm) deep for the head to sit flush. As cross-checks, the same diameters at 90 degrees give exactly 0.1250 in (half the diameter difference), and a 12 mm countersink over a 6 mm hole gives 3.451 mm at 82 degrees, 3.000 mm at 90 degrees and 2.517 mm at 100 degrees, matching published worked examples.

Benefits of Using a Countersink Depth Calculator

  • Gives the depth to cut, not the tip depth: the result is measured from the surface to where the cone meets the hole, which is the figure a depth stop or DRO needs.
  • Covers the standard angles in one click: presets for 82, 90, 100, 110 and 120 degrees, matching inch, metric and aerospace practice.
  • Shows inches and millimetres together: the depth is given in both units, so a metric drawing and an inch tool can be used together.
  • Compares angles side by side: the Compare Angles tab shows how much shallower the cut gets as the angle opens up.
  • Explains the maths: the diameter difference, half angle and depth factor are all shown, so the result can be checked by hand.
  • Free and instant: no sign-up, no download, and the results and diagram update as you type.

Frequently Asked Questions

What is the formula for countersink depth?

Depth = (D – d) / (2 x tan(angle / 2)), where D is the countersink diameter at the surface, d is the hole diameter, and the angle is the included angle of the countersink. For a 0.5 in countersink over a 0.25 in hole at 82 degrees, the depth is (0.5 – 0.25) / (2 x tan(41 deg)) = 0.25 / 1.7386 = 0.1438 in. The angle in the formula is the included angle, not the half angle, so do not halve it before entering it.

What countersink angle should I use, 82 or 90 degrees?

Match the angle to the screw standard. Inch flat head screws use an 82 degree countersink (ASME B18.6.3), metric flat head screws use 90 degrees (ISO 7046), and aerospace fasteners commonly use 100 degrees. Using the wrong angle leaves the head sitting on a ring instead of seating on the full cone, which looks wrong and loads the screw unevenly. The preset buttons cover all three, plus 110 and 120 degrees.

Is the depth measured to the tip of the countersink tool?

No. The depth this calculator gives is measured from the workpiece surface down to where the cone meets the hole wall, which is the depth a depth stop or DRO should be set to. The pointed tip of the tool goes deeper than that, and a tool with a flat or rounded tip has its own offset. Touch off on the surface, then cut to the depth shown here, and check the resulting mouth diameter with a countersink gauge if the fit matters.

Why does a wider countersink angle need less depth?

Because the depth is the radial difference divided by twice the tangent of half the angle, and the tangent grows as the angle opens up. At 82 degrees the depth factor is 0.5752, at 90 degrees it is 0.5000, and at 120 degrees it is only 0.2887, so the same head diameter needs about half the depth at 120 degrees that it needs at 82 degrees. The Compare Angles tab shows this directly for your diameters.

What hole size should I drill before countersinking?

Drill the clearance hole for the screw first, then countersink into it. The hole diameter is the d in the formula, so a larger hole needs less countersink depth to reach the same head diameter. Use the Clearance Hole Calculator to find the normal clearance hole for your screw size, then enter that diameter here with the head diameter to get the depth.

Disclaimer

This calculator computes countersink depth from the dimensions you enter, using the standard cone formula depth = (D – d) / (2 x tan(angle / 2)) for an ideal sharp cone meeting a straight cylindrical hole. Real tools have flat or rounded tips, and real holes have tolerances, burrs and coatings, so the actual mouth diameter can differ slightly from the ideal figure. For flush fits that matter, check the finished countersink with a gauge and confirm the screw head diameter and angle against the fastener standard (ASME B18.6.3 for inch flat heads, ISO 7046 for metric) rather than relying on a calculator alone.

ADVERTISEMENT

ADVERTISEMENT